TN Cat 7 Review Questions with correct Answers-

TN Cat 7 Review Questions with correct Answers- D. EPA - AnswerWhich agency is responsible for the enforcement of federal laws and regulations? A. UT B. TDA C. USDA D. EPA /.B. FIFRA - AnswerWhich law requires federal registration of pesticides shipped in interstate commerce? A. TIFRA B. FIFRA C. FEPCA D. TAPA /.B. FEPCA - AnswerWhich law prohibits the use of any registered pesticide in a manner inconsistent with label directions? A. TAPA B. FEPCA C. USDA D. RCRA /.A. $5,000 - AnswerAny Commercial Applicator who violates any provision of FIFRA may be assessed a civil penalty of? A. $5,000 B. $10,000 C. $15,000 D. $20,000 /.C. TDA - AnswerWhich agency is responsible for the protection of the health, safety and welfare of pest control employees and the general public from the hazards of pesticide use in Tennessee? A. USDA B. DOT C. TDA D. TDOT /.B. Regulatory Services Division - AnswerThe TDA certification and enforcement functions are coordinated primarily through what division of TDA? A. Division of Plant Industries B. Regulatory Services Division C. Fishery and Wildlife D. Pesticide Regulatory Division /.C. Restricted-use pesticides - AnswerPesticides that may cause adverse effects on the environment and/or the applicator, unless subject to additional regulatory restrictions are classified as? A. General-use pesticides B. Unclassified C. Restricted-use pesticides D. Commercial-use pesticides /.C. 3 years - AnswerA certification period lasts for how many years? A. 5 years B. 4 years C. 3 years D. 2 years /.D. 50% - AnswerOne may earn up to what percentage in-house points in the re-certification program? A. 10% B. 80% C. 30% D. 50% /.A. 30 - AnswerHow many re-certification points are required for Category 7 in a 3 year period? A. 30 B. 6 C. 10 D. 4 /.B. Scheduled pesticide applications - AnswerWhich is NOT a step in an IPM program? A. Inspection B. Scheduled pesticide applications C. Determination of pest thresholds D. Monitoring of pest populations and management program. /.D. Locate pesticide drift - AnswerWhich is NOT an objective of a general inspection? A. Confirm pest identity and presence B. Identify the location and source of the pest problem. C. Determine the extent of the pest infestation. D. Locate pesticide drift. /.A. True - AnswerA good inspection technique is to first identify areas within a structure that offer a tropical environment (warmth, moist, dark and humid). A. True B. False /.D. Color pattern in a rug - AnswerWhich is NOT likely to be used as a pest travel route? A. Conduit B. Electrical wires C. Pipes D. Color pattern in a rug /.C. Using a vacuum to remove pests. - AnswerWhich is NOT an example of pest-proofing? A. Building gaps reduced to 1/4 inch opening. B. Vents Screened with 1/4 inch mesh. C. Using a vacuum to remove pests. D. Sealing areas where utility lines enter a structure. /.A. where a pest lives naturally and has access to food, water and harborage. - AnswerHabitat is a location A. where a pest lives naturally and has access to food, water and harborage. B. with many cracks and crevices C. with many branches to increase diversity. D. is a door, window or other opening into a structure. /.C. Use of harpoon mole traps. - AnswerWhich is NOT an example of pest habitat manipulation? A. Installation of prickly wires on a building ledge. B. Good sanitation C. Use of Harpoon mole traps D. Reduce the humidity in a basement /.D. Multiple-catch traps - AnswerWhich is NOT an example of a lethal trapping program? A. Rodent snap traps B. Insect light traps C. Harpoon mole traps D. Multiple-catch traps /.B. Integrated Pest Management - AnswerIPM stands for A. Insect Pest Management B. Integrated Pest Management C. Integrated Pesticide Management D. Insect and Pesticide Management /.A. Inspection, Pest threshold determination, Management procedures and Evaluation. - AnswerThe four main components of IPM listed in this manual are: A. Inspection, Pest threshold determination, Management procedures and Evaluation. B. Inspection, Perimeter treatments, Management procedures and Evaluation. C. Inspection, Identification, Management procedures and Evaluation.