Redo Multimeter Test UPDATED Actual
Exam Questions and CORRECT Answers
After testing the fuses it was determined that the 0.5 amp fuse was bad. Student A indicates
they do NOT have an exact replacement fuse, but a cheaper replacement fuse of similar size
is acceptable to use. Student B states the correct replacement fuse is specially designed to
protect the user in case of an unexpected high amperage draw. Who is correct? - CORRECT
ANSWER✔✔✔- Student B
A student uses a multimeter to measure a resistance of a wire and gets a reading of 7.4 k?
What would this value be in ohms ? - CORRECT ANSWER✔✔✔- 7400 ohms
The function buttons on the meter may be used to ______ - CORRECT ANSWER✔✔✔-
Both A and B
Using the illustration, with the rotary dial set to test micro-amps which two test lead terminal
locations should be used? - CORRECT ANSWER✔✔✔- Terminals 2 and 3
A student can compare known values to measured values when using the REL function of the
multimeter - CORRECT ANSWER✔✔✔- True
Of the following four diagnostic products which is the best suited for making exact voltage
measurements when pinpoint testing an electronic circuit. - CORRECT ANSWER✔✔✔-
High impedance digital multi-meter
Safety is a concern when using the test instruments. Protect yourself by testing the meters for
one of the following before conducting any tests. - CORRECT ANSWER✔✔✔- Test leads
for breaks for damage.
Safety is a concern when using the test instruments. You can protect yourself by testing the
meters for one of the following before conducting any tests. - CORRECT ANSWER✔✔✔-
Test for good meter fuses
, Student A states using the Amperage setting on the multi meter you can measure the current
flow in a circuit. Student B states that the Frequency setting is used to test for Ohms. Who is
correct? - CORRECT ANSWER✔✔✔- Student A
The bar graph on the display enables the user to see __________ more easily. - CORRECT
ANSWER✔✔✔- rapidly changing signals
To capture a maximum value automatically during testing, which function button would you
press? - CORRECT ANSWER✔✔✔- REC
Using the illustration, with the rotary dial set to measure capacitance which two test leads
terminal location should be used? - CORRECT ANSWER✔✔✔- Terminals 3 and 4
When using the meter in the Frequency setting you are measuring what? - CORRECT
ANSWER✔✔✔- The number of times per second a signal happens
Which of the following rotary dial setting would be best for measuring the number of cycles
per second. - CORRECT ANSWER✔✔✔- Hz
The meter is set-up and testing mV but an OL reading is displayed to correct this situation.
Student A state the REL button should be pressed. Student B state the RANGE button should
be pressed. Who is correct? - CORRECT ANSWER✔✔✔- Student B
Which function button sets the display to zero and factors out undesired reading? -
CORRECT ANSWER✔✔✔- REL
Two Students are discussing the HOLD function button. Student A states the HOLD button
will pause or freeze the screen to capture a reading. Student B states the pressing the HOLD
button again will return to the live electrical reading. Who is correct? - CORRECT
ANSWER✔✔✔- Both Student A and Student B
What does it mean when a meter has "high-impedance" - CORRECT ANSWER✔✔✔- Can
measure a high voltage
Exam Questions and CORRECT Answers
After testing the fuses it was determined that the 0.5 amp fuse was bad. Student A indicates
they do NOT have an exact replacement fuse, but a cheaper replacement fuse of similar size
is acceptable to use. Student B states the correct replacement fuse is specially designed to
protect the user in case of an unexpected high amperage draw. Who is correct? - CORRECT
ANSWER✔✔✔- Student B
A student uses a multimeter to measure a resistance of a wire and gets a reading of 7.4 k?
What would this value be in ohms ? - CORRECT ANSWER✔✔✔- 7400 ohms
The function buttons on the meter may be used to ______ - CORRECT ANSWER✔✔✔-
Both A and B
Using the illustration, with the rotary dial set to test micro-amps which two test lead terminal
locations should be used? - CORRECT ANSWER✔✔✔- Terminals 2 and 3
A student can compare known values to measured values when using the REL function of the
multimeter - CORRECT ANSWER✔✔✔- True
Of the following four diagnostic products which is the best suited for making exact voltage
measurements when pinpoint testing an electronic circuit. - CORRECT ANSWER✔✔✔-
High impedance digital multi-meter
Safety is a concern when using the test instruments. Protect yourself by testing the meters for
one of the following before conducting any tests. - CORRECT ANSWER✔✔✔- Test leads
for breaks for damage.
Safety is a concern when using the test instruments. You can protect yourself by testing the
meters for one of the following before conducting any tests. - CORRECT ANSWER✔✔✔-
Test for good meter fuses
, Student A states using the Amperage setting on the multi meter you can measure the current
flow in a circuit. Student B states that the Frequency setting is used to test for Ohms. Who is
correct? - CORRECT ANSWER✔✔✔- Student A
The bar graph on the display enables the user to see __________ more easily. - CORRECT
ANSWER✔✔✔- rapidly changing signals
To capture a maximum value automatically during testing, which function button would you
press? - CORRECT ANSWER✔✔✔- REC
Using the illustration, with the rotary dial set to measure capacitance which two test leads
terminal location should be used? - CORRECT ANSWER✔✔✔- Terminals 3 and 4
When using the meter in the Frequency setting you are measuring what? - CORRECT
ANSWER✔✔✔- The number of times per second a signal happens
Which of the following rotary dial setting would be best for measuring the number of cycles
per second. - CORRECT ANSWER✔✔✔- Hz
The meter is set-up and testing mV but an OL reading is displayed to correct this situation.
Student A state the REL button should be pressed. Student B state the RANGE button should
be pressed. Who is correct? - CORRECT ANSWER✔✔✔- Student B
Which function button sets the display to zero and factors out undesired reading? -
CORRECT ANSWER✔✔✔- REL
Two Students are discussing the HOLD function button. Student A states the HOLD button
will pause or freeze the screen to capture a reading. Student B states the pressing the HOLD
button again will return to the live electrical reading. Who is correct? - CORRECT
ANSWER✔✔✔- Both Student A and Student B
What does it mean when a meter has "high-impedance" - CORRECT ANSWER✔✔✔- Can
measure a high voltage
