ASE CERTIFICATION QUESTIONS AND ANSWERS
Both b and c - Answers -Coolant should be tested for ________.
Proper color
Freezing point (temperature)
Specific Gravity
Both b and c
Both technician a and b - Answers -Two technicians are discussing a compression test.
Technician A says that the engine should be cranked over with the pressure gauge
installed for "4 puffs." Technician B says that the maximum difference between the
highest reading cylinder and the lowest reading cylinder should be 20%. Which
technician is correct?
Technician A only
Technician b only
Both Technician A and B
Neither technician a nor b
Technician B - Answers -Technician A says that oil should be squirted into all the
cylinders before taking a compression test. Technician B says that if the compression
greatly increases when some oil is squirted in the cylinders, it indicates defective or
worn piston rings.
Technician A
Technician B
Both technicians
Neither technician
Technician B - Answers -During a cylinder leakage (leak-down) test, air is noticed
coming out of the oil fill opening. Technician A says that the oil filter my be logged.
Technician B says that the piston rings may be worn or defective. Which technician is
correct?
Technician A
Technician B
Both A and B
Neither A nor B
All of the above - Answers -The tires on an all-wheel-drive vehicle should all be
_____________
Same brand and size
Same inflation pressure
, Within 1/16 inch of the same tread depth
All of the above
Removing the airbag modules from the vehicle - Answers -Which step is NOT usually
done when disarming an airbag system?
Removing airbag modules from the vehicle
Removing the airbag fuse
Disconnecting the electrical connector to the airbag
Disconnecting the battery
Any of the above - Answers -Where can the type of power steering fluid be found?
On the reservoir fill cap
In the owner's manual
In service information
Any of the above
Length - Answers -Accessory drive belts are checked for all except.
Cracks
Wear
Length
Alignment
Raise the front wheel off the ground and turn the steering wheel lock to lock - Answers -
Which is the preferred method to bleed air from a power steering system?
Raise the front wheel off the ground and turn the steering wheel lock to lock
Start the engine and allow to idle
Use a vacuum pump attached to the reservoir cap
Use a bleeding tool
All of the above - Answers -When replacing steering or suspension parts, which
precaution is needed to be performed?
Fasteners tighten to factory specifications
Most parts need to be replaced in pair (left and right side)
The front wheels should be in the straight ahead position when the final parts are
tighten
All of the above
shock absorber - Answers -A steering dampener looks like a ___________.
Bump stop
Shock absorber
Both b and c - Answers -Coolant should be tested for ________.
Proper color
Freezing point (temperature)
Specific Gravity
Both b and c
Both technician a and b - Answers -Two technicians are discussing a compression test.
Technician A says that the engine should be cranked over with the pressure gauge
installed for "4 puffs." Technician B says that the maximum difference between the
highest reading cylinder and the lowest reading cylinder should be 20%. Which
technician is correct?
Technician A only
Technician b only
Both Technician A and B
Neither technician a nor b
Technician B - Answers -Technician A says that oil should be squirted into all the
cylinders before taking a compression test. Technician B says that if the compression
greatly increases when some oil is squirted in the cylinders, it indicates defective or
worn piston rings.
Technician A
Technician B
Both technicians
Neither technician
Technician B - Answers -During a cylinder leakage (leak-down) test, air is noticed
coming out of the oil fill opening. Technician A says that the oil filter my be logged.
Technician B says that the piston rings may be worn or defective. Which technician is
correct?
Technician A
Technician B
Both A and B
Neither A nor B
All of the above - Answers -The tires on an all-wheel-drive vehicle should all be
_____________
Same brand and size
Same inflation pressure
, Within 1/16 inch of the same tread depth
All of the above
Removing the airbag modules from the vehicle - Answers -Which step is NOT usually
done when disarming an airbag system?
Removing airbag modules from the vehicle
Removing the airbag fuse
Disconnecting the electrical connector to the airbag
Disconnecting the battery
Any of the above - Answers -Where can the type of power steering fluid be found?
On the reservoir fill cap
In the owner's manual
In service information
Any of the above
Length - Answers -Accessory drive belts are checked for all except.
Cracks
Wear
Length
Alignment
Raise the front wheel off the ground and turn the steering wheel lock to lock - Answers -
Which is the preferred method to bleed air from a power steering system?
Raise the front wheel off the ground and turn the steering wheel lock to lock
Start the engine and allow to idle
Use a vacuum pump attached to the reservoir cap
Use a bleeding tool
All of the above - Answers -When replacing steering or suspension parts, which
precaution is needed to be performed?
Fasteners tighten to factory specifications
Most parts need to be replaced in pair (left and right side)
The front wheels should be in the straight ahead position when the final parts are
tighten
All of the above
shock absorber - Answers -A steering dampener looks like a ___________.
Bump stop
Shock absorber
