Please write clearly in block capitals.
Centre number Candidate number
Surname
Forename(s)
Candidate signat ure
GCSE
ENGINEERING
Unit 1 Written Paper
Wednesday 22 May 2024 Morning Time allowed: 2 hours
Materials
For Examiner’s Use
For this paper you must have:
• normal writing and drawing instruments Question Mark
• a calculator.
1
Instructions 2
• Use black ink or black ball-point pen. Use pencil only for drawing. 3
• Fill in the boxes at the top of this page. 4
• Answer all questions.
5
• You must answer the questions in the spaces provided. Do not write
outside the box around each page or on blank pages. 6
• Some questions will require you to shade a circle. If you make a mistake 7
cross through the incorrect answer.
8
• Do all rough work in this book. Cross through any work you do not want
to be marked. 9
10
Information 11
• The marks for questions are shown in brackets.
12
• The maximum mark for this paper is 120.
• You are reminded of the need for good English and clear presentation in your TOTAL
answers.
*jun19 52W01*
IB/M/Jun19/E9 8852/W
, 2
Do not write
outside the
Answer all questions in the spaces provided. box
For each answer completely fill in the circle alongside the appropriate answer.
CORRECT METHOD WRONG METHODS
If you want to change your answer you must cross out your original answer as shown.
If you wish to return to an answer previously crossed out, ring the answer you now wish to select
as shown.
0 1
.1 The list below shows a range of different materials.
Shade the circles next to the two alloys.
[2 marks]
A Aluminium
B Brass
C Bronze
D Copper
E Lead
F Zinc
0 1
.2 Which one of the following properties best describes the ability of steel to be pressed
or rolled into thin sheets?
[1 mark]
A Ductility
B Hardness
C Malleability
D Toughness
*02*
IB/M/Jun19/8852/W
, 3
Do not write
outside the
box
0 1 . 3 Complete the following statement using the word bank provided.
[3 marks]
Annealing is a heat treatment process which reduces the of a
material, and helps to increase its . Some materials, like
copper, can be cooled quickly during the annealing process by .
Word bank
ductility, galvanising, hardness, normalising, quenching, sintering, stiffness,
strength, toughness
0 1
.4 Shade one circle that gives the name of the process described below:
The joining of two metal parts by heating both surfaces together to the point of
melting.
[1 mark]
A Brazing
B Milling
C Soldering
D Welding
0 1
.5 Which of the following shows a dimension of more than 35 mm?
[1 mark]
A = 35 mm
B < 35 mm
C > 35 mm
D ± 35 mm
Turn over ►
*03*
IB/M/Jun19/8852/W
Centre number Candidate number
Surname
Forename(s)
Candidate signat ure
GCSE
ENGINEERING
Unit 1 Written Paper
Wednesday 22 May 2024 Morning Time allowed: 2 hours
Materials
For Examiner’s Use
For this paper you must have:
• normal writing and drawing instruments Question Mark
• a calculator.
1
Instructions 2
• Use black ink or black ball-point pen. Use pencil only for drawing. 3
• Fill in the boxes at the top of this page. 4
• Answer all questions.
5
• You must answer the questions in the spaces provided. Do not write
outside the box around each page or on blank pages. 6
• Some questions will require you to shade a circle. If you make a mistake 7
cross through the incorrect answer.
8
• Do all rough work in this book. Cross through any work you do not want
to be marked. 9
10
Information 11
• The marks for questions are shown in brackets.
12
• The maximum mark for this paper is 120.
• You are reminded of the need for good English and clear presentation in your TOTAL
answers.
*jun19 52W01*
IB/M/Jun19/E9 8852/W
, 2
Do not write
outside the
Answer all questions in the spaces provided. box
For each answer completely fill in the circle alongside the appropriate answer.
CORRECT METHOD WRONG METHODS
If you want to change your answer you must cross out your original answer as shown.
If you wish to return to an answer previously crossed out, ring the answer you now wish to select
as shown.
0 1
.1 The list below shows a range of different materials.
Shade the circles next to the two alloys.
[2 marks]
A Aluminium
B Brass
C Bronze
D Copper
E Lead
F Zinc
0 1
.2 Which one of the following properties best describes the ability of steel to be pressed
or rolled into thin sheets?
[1 mark]
A Ductility
B Hardness
C Malleability
D Toughness
*02*
IB/M/Jun19/8852/W
, 3
Do not write
outside the
box
0 1 . 3 Complete the following statement using the word bank provided.
[3 marks]
Annealing is a heat treatment process which reduces the of a
material, and helps to increase its . Some materials, like
copper, can be cooled quickly during the annealing process by .
Word bank
ductility, galvanising, hardness, normalising, quenching, sintering, stiffness,
strength, toughness
0 1
.4 Shade one circle that gives the name of the process described below:
The joining of two metal parts by heating both surfaces together to the point of
melting.
[1 mark]
A Brazing
B Milling
C Soldering
D Welding
0 1
.5 Which of the following shows a dimension of more than 35 mm?
[1 mark]
A = 35 mm
B < 35 mm
C > 35 mm
D ± 35 mm
Turn over ►
*03*
IB/M/Jun19/8852/W
