STUVIA?_APPROVED??
, STUVIA?_APPROVED??
TABLE OF CONTENTS
Test Bank: Electrical Wiring Commercial 18th Edition
Authors: Phil Simmons, Ray Mullin, Mark Ode
1. Commercial Building Plans and Specifications.
2. Reading Electrical Working Drawings--Entry Level.
3. General Requirements for Conductors.
4. Branch Circuits.
5. Switches and Receptacles.
6. Wiring Methods.
7. Motor and Appliance Circuits.
8. Feeder Installation and Load Calculation.
9. Special Systems.
10. Working Drawings--Upper Level.
11. Special Circuits (Owner's Circuits).
12. Panelboard Selection and Installation.
13. The Electric Service and Grounding.
14. Lamps and Ballasts for Lighting.
15. Luminaires.
16. Emergency, Legally Required Standby and Optional Standby Power Systems.
17. Overcurrent Protection: Fuses and Circuit Breakers.
18. Short-Circuit Calculations and Coordination of Overcurrent Protective Devices.
19. Equipment and Conductor Short-Circuit Protection.
20. Low-Voltage Remote Control.
21. The Cooling System.
22. Commercial Utility-Interactive Photovoltaic Systems.
, STUVIA?_APPROVED??
Name Clas Dat
: s: e:
Chapter 01 Commercial Building Plans and Specifications
1. Allowing metal shavings from drilling switchboard busing to fall onto energized parts of electrical equipment generally
results in a(n) , which can cause deadly burns.
a. lockout
b. arc blast
c. tagout
d. pressure
wave
ANSWER: b
POINTS: 1
REFERENCES: Safety in the Workplace
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 2:32 AM
DATE MODIFIED: 7/26/2023 9:23 PM
2. The NEC® defines a(n) as one who has skills and knowledge related to the construction and operation of electrical
equipment and installations and has received safety training to recognize and avoid the hazards involved.
a. qualified
person
b. engineer
c. expert
d. employee
ANSWER: a
POINTS: 1
REFERENCES: Safety in the Workplace
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 2:39 AM
DATE MODIFIED: 7/7/2023 3:59 AM
3. On large electrical installations, an arc flash can generate temperatures of .
a. 15,000°F (8,316°C)
b. 25,000°F (13871°C)
c. 35,000°F (19,427°C)
d. 45,000°F (24982°C)
ANSWER: c
POINTS: 1
REFERENCES: Safety in the Workplace
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 3:14 AM
DATE MODIFIED: 7/7/2023 3:14 AM
, STUVIA?_APPROVED??
Name Clas Dat
: s: e:
Chapter 01 Commercial Building Plans and Specifications
4. When turning a standard disconnect switch on, of the switch.
a. do not stand to the right
b. do not stand to the left
c. always stand in front
d. do not stand directly in
front
ANSWER: d
POINTS: 1
REFERENCES: Safety in the Workplace
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 3:20 AM
DATE MODIFIED: 7/7/2023 3:21 AM
5. Which item in the general clauses and conditions is of value to the contractor and the estimator only?
a. Proposal
b. Schedule of
drawings
c. Agreement
d. Notice to bidders
ANSWER: d
POINTS: 1
REFERENCES: Commercial Building Specifications
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 3:21 AM
DATE MODIFIED: 7/7/2023 3:57 AM
6. According to the supplementary general conditions, who is responsible for any utilities that are damaged?
a. the municipal
government
b. the contractor
c. the crew
d. the site owner
ANSWER: b
POINTS: 1
REFERENCES: Commercial Building Specifications
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 3:22 AM
DATE MODIFIED: 7/7/2023 3:57 AM
7. The construction plans for a building are often called .
.. Page 2
, STUVIA?_APPROVED??
TABLE OF CONTENTS
Test Bank: Electrical Wiring Commercial 18th Edition
Authors: Phil Simmons, Ray Mullin, Mark Ode
1. Commercial Building Plans and Specifications.
2. Reading Electrical Working Drawings--Entry Level.
3. General Requirements for Conductors.
4. Branch Circuits.
5. Switches and Receptacles.
6. Wiring Methods.
7. Motor and Appliance Circuits.
8. Feeder Installation and Load Calculation.
9. Special Systems.
10. Working Drawings--Upper Level.
11. Special Circuits (Owner's Circuits).
12. Panelboard Selection and Installation.
13. The Electric Service and Grounding.
14. Lamps and Ballasts for Lighting.
15. Luminaires.
16. Emergency, Legally Required Standby and Optional Standby Power Systems.
17. Overcurrent Protection: Fuses and Circuit Breakers.
18. Short-Circuit Calculations and Coordination of Overcurrent Protective Devices.
19. Equipment and Conductor Short-Circuit Protection.
20. Low-Voltage Remote Control.
21. The Cooling System.
22. Commercial Utility-Interactive Photovoltaic Systems.
, STUVIA?_APPROVED??
Name Clas Dat
: s: e:
Chapter 01 Commercial Building Plans and Specifications
1. Allowing metal shavings from drilling switchboard busing to fall onto energized parts of electrical equipment generally
results in a(n) , which can cause deadly burns.
a. lockout
b. arc blast
c. tagout
d. pressure
wave
ANSWER: b
POINTS: 1
REFERENCES: Safety in the Workplace
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 2:32 AM
DATE MODIFIED: 7/26/2023 9:23 PM
2. The NEC® defines a(n) as one who has skills and knowledge related to the construction and operation of electrical
equipment and installations and has received safety training to recognize and avoid the hazards involved.
a. qualified
person
b. engineer
c. expert
d. employee
ANSWER: a
POINTS: 1
REFERENCES: Safety in the Workplace
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 2:39 AM
DATE MODIFIED: 7/7/2023 3:59 AM
3. On large electrical installations, an arc flash can generate temperatures of .
a. 15,000°F (8,316°C)
b. 25,000°F (13871°C)
c. 35,000°F (19,427°C)
d. 45,000°F (24982°C)
ANSWER: c
POINTS: 1
REFERENCES: Safety in the Workplace
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 3:14 AM
DATE MODIFIED: 7/7/2023 3:14 AM
, STUVIA?_APPROVED??
Name Clas Dat
: s: e:
Chapter 01 Commercial Building Plans and Specifications
4. When turning a standard disconnect switch on, of the switch.
a. do not stand to the right
b. do not stand to the left
c. always stand in front
d. do not stand directly in
front
ANSWER: d
POINTS: 1
REFERENCES: Safety in the Workplace
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 3:20 AM
DATE MODIFIED: 7/7/2023 3:21 AM
5. Which item in the general clauses and conditions is of value to the contractor and the estimator only?
a. Proposal
b. Schedule of
drawings
c. Agreement
d. Notice to bidders
ANSWER: d
POINTS: 1
REFERENCES: Commercial Building Specifications
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 3:21 AM
DATE MODIFIED: 7/7/2023 3:57 AM
6. According to the supplementary general conditions, who is responsible for any utilities that are damaged?
a. the municipal
government
b. the contractor
c. the crew
d. the site owner
ANSWER: b
POINTS: 1
REFERENCES: Commercial Building Specifications
QUESTION TYPE: Multiple Choice
HAS VARIABLES: False
DATE CREATED: 7/7/2023 3:22 AM
DATE MODIFIED: 7/7/2023 3:57 AM
7. The construction plans for a building are often called .
.. Page 2
