CT - F-2 UNLIMITED JOURNEYPERSON (FIRE SPRINKLER) | COMPLETE REAL EXAM 2026/2027 | QUESTIONS AND 100% VERIFIED ANSWERS | PASS GUARANTEE

CT - F-2 UNLIMITED JOURNEYPERSON (FIRE SPRINKLER) | COMPLETE
REAL EXAM 2026/2027 | QUESTIONS AND 100% VERIFIED ANSWERS |
PASS GUARANTEE




(CT) F-2 Unlimited Journeyperson (Fire Sprinkler)




Q: Who issues the F-2 Unlimited Journeyperson Fire Sprinkler license in
Connecticut?
ANSWER The Connecticut Department of Consumer Protection (DCP).
Q: How many hours of verifiable experience are required to sit for the CT F-2
exam?
ANSWER 8,000 hours (approximately 4 years).
Q: Under whose direct supervision must an F-2 apprentice work?
ANSWER A licensed F-1 Unlimited Fire Sprinkler Contractor.
Q: What is the penalty for performing sprinkler work in CT without a license?
ANSWER Misdemeanor charges and fines.
Q: How often must the CT F-2 Journeyperson license be renewed?
ANSWER Every two years.
Q: Are Continuing Education Units (CEUs) required for CT F-2 renewal?
ANSWER No, CT does not currently mandate CEUs for this specific license
renewal.
Q: What OSHA regulation covers fall protection in construction?
ANSWER 29 CFR 1926 Subpart M.

,Q: At what height does OSHA require fall protection on a walking/working
surface?
ANSWER 6 feet.
Q: What type of lanyard is required for fall arrest?
ANSWER A shock-absorbing lanyard.
Q: What is the maximum free-fall distance allowed with a shock-absorbing
lanyard?
ANSWER 6 feet.
Q: What is the minimum breaking strength required for a safety harness D-
ring?
ANSWER 5,000 lbs.
Q: What OSHA standard regulates trenching and excavation safety?
ANSWER 29 CFR 1926 Subpart P.
Q: At what depth must a trench be protected by a shoring system, sloping, or
shielding?
ANSWER 5 feet.
Q: What does "Competent Person" mean in trenching operations?
ANSWER Someone capable of identifying existing and predictable hazards and
has authority to take corrective measures.
Q: What is the maximum allowable slope for a Type C soil in an excavation?
ANSWER 1.5H:1V (34 degrees).
Q: What must be provided to access/egress a trench deeper than 4 feet?
ANSWER A ladder, stairway, or ramp within 25 feet of lateral travel.
Q: What is the minimum required Personal Protective Equipment (PPE) on a
construction site?
ANSWER Hard hat, safety glasses, steel-toed boots, high-visibility vest.
Q: What type of fire extinguisher is required for a hot work permit?
ANSWER A minimum 20BC rated extinguisher.

, Q: What does NFPA 51B govern?
ANSWER Fire prevention during welding, cutting, and other hot work.
Q: How far must a hot work area be cleared of combustibles?
ANSWER 35 feet.
Q: What is the minimum safe distance a fire watch must be maintained after
hot work?
ANSWER 30 minutes.
Q: What is the primary purpose of a Material Safety Data Sheet (SDS)?
ANSWER To provide information on the hazards, handling, and PPE for
specific chemicals.
Q: What does GHS stand for on an SDS?
ANSWER Globally Harmonized System.
Q: What is the OSHA limit for worker exposure to lead?
ANSWER 50 micrograms per cubic meter of air over an 8-hour TWA.
Q: What type of respirator is typically required when cutting threaded pipe
with an oil-based cutting fluid?
ANSWER N95 or half-face with organic vapor cartridges.
Q: What is the proper way to store acetylene cylinders?
ANSWER Upright, valve capped, and chained to a fixed support.
Q: What is the minimum safe distance between an oxygen cylinder and a fuel
gas cylinder (like acetylene) in storage?
ANSWER 20 feet, or a 5-foot non-combustible wall with a 1/2-hour fire rating.
Q: What does Lockout/Tagout (LOTO) refer to?
ANSWER Ensuring a machine or energy source is zero-energy state before
servicing.
Q: What is the correct sequence for applying LOTO?
ANSWER Notify, shutdown, isolate, lockout, tag, verify zero energy.
Q: What is "Arc Flash"?