MSSC QUALITY ACTUAL TEST QUESTIONS
WITH COMPLETE SOLUTION PREMIUM
REVIEW CONTENT
●● The three standard views of an object are ____________
Answer: top, front, right side
●● Geometric dimensioning and tolerances refers to tolerances which
control
Answer: Form, profile, orientation, location, and runout
●● Which type of feature is parallel to the surface being dimensioned?
Answer: dimension lines
●● To establish on a drawing that 1/8 inch equals 1 inch, the designer
would write ____________.
Answer: 1/8 = 1
●● If the feature on the drawing is drawn 2 inched long and the scale is
1:4, what is the actual dimension of the object?
Answer: 8"
,●● If a box of parts weighs 30 pounds, how many kilograms does it
weigh?
Answer: 13.6 kilograms
●● The acronym, ECN, stands for:
Answer: Engineering Change Notice
●● A capable manufacturing process tends to run
Answer: out of control
●● The acronym, SPC, stands for
Answer: Statistical process control
●● Adjustments in follow-up with product quality checks are necessary
in a/an _______ non-conformity
Answer: Product process and system
●● Recommendations for corrective action are the responsibility of
Answer: All knowledgeable persons
●● To convert inches to millimeters, multiply inches by:
Answer: 25.4
, ●● Identify a device that measures length to an accuracy of 0.001 inch.
Answer: Micrometer
●● A ________ is the total amount by which a specified dimension is
allowed to vary and still be a good part
Answer: tolerance
●● Which of the following measurement tools should be selected to
measure a part that has a length specification of 1.625 inches +/- 0.005?
Answer: micrometer
●● A part measures 45.70 mm in a process with the tolerance of 46mm +
or - .28 is considered ____________.
Answer: Out of spec, below the lower tolerance limit
●● When connected to a PC, a digital caliper can be used to:
Answer: Collect SPC data
●● The equipment at a workstation is supposed to produce parts at
2.593. per the part drawing, and has a spec limit of + or - 0.004. is the
part that has been produces at 2.590 out of spec?
Answer: No, it is not out of spec
WITH COMPLETE SOLUTION PREMIUM
REVIEW CONTENT
●● The three standard views of an object are ____________
Answer: top, front, right side
●● Geometric dimensioning and tolerances refers to tolerances which
control
Answer: Form, profile, orientation, location, and runout
●● Which type of feature is parallel to the surface being dimensioned?
Answer: dimension lines
●● To establish on a drawing that 1/8 inch equals 1 inch, the designer
would write ____________.
Answer: 1/8 = 1
●● If the feature on the drawing is drawn 2 inched long and the scale is
1:4, what is the actual dimension of the object?
Answer: 8"
,●● If a box of parts weighs 30 pounds, how many kilograms does it
weigh?
Answer: 13.6 kilograms
●● The acronym, ECN, stands for:
Answer: Engineering Change Notice
●● A capable manufacturing process tends to run
Answer: out of control
●● The acronym, SPC, stands for
Answer: Statistical process control
●● Adjustments in follow-up with product quality checks are necessary
in a/an _______ non-conformity
Answer: Product process and system
●● Recommendations for corrective action are the responsibility of
Answer: All knowledgeable persons
●● To convert inches to millimeters, multiply inches by:
Answer: 25.4
, ●● Identify a device that measures length to an accuracy of 0.001 inch.
Answer: Micrometer
●● A ________ is the total amount by which a specified dimension is
allowed to vary and still be a good part
Answer: tolerance
●● Which of the following measurement tools should be selected to
measure a part that has a length specification of 1.625 inches +/- 0.005?
Answer: micrometer
●● A part measures 45.70 mm in a process with the tolerance of 46mm +
or - .28 is considered ____________.
Answer: Out of spec, below the lower tolerance limit
●● When connected to a PC, a digital caliper can be used to:
Answer: Collect SPC data
●● The equipment at a workstation is supposed to produce parts at
2.593. per the part drawing, and has a spec limit of + or - 0.004. is the
part that has been produces at 2.590 out of spec?
Answer: No, it is not out of spec
