BIPC 620 Exam Questions & Answers
(Grade A+)
Certified IPC Trainer CIT and Certified IPC Specialist certifications
expire after how many years -
correct answer ✅2 Years
Master IPC Trainers MIT are authorized to certify -
correct answer ✅CIT and CIS only
A CIT is authorized to certify -
correct answer ✅CIS
If permitted by company policy, a CIT may grant an extension of up
to how many days -
correct answer ✅90 days
What module is required as a pre req. for IPC 620 CIS certification -
correct answer ✅Module 1
CIS retesting may be taken only after a minimum of -
correct answer ✅24 hours
,BIPC 620 Exam Questions & Answers
(Grade A+)
What is the correct order of production status -
correct answer ✅Design, PCB Fabrication, Assemly, Cleaning and
Coating
The tolerance for magnification aid is -
correct answer ✅Plus or Minus 15 (Chapter 1) Page 1-7
The Manufacturer shall (_1_2_3) have a documented calibration
system -
correct answer ✅N1D2D3 - PAGE 1-8
What is a Process Indicator -
correct answer ✅A condition that identifies a characteristics that
does not affect the form fit or function of a product- should be
monitored
Conditions that are not specified as defective or as a process
indicator are considered -
correct answer ✅Acceptable - Page 1-4
Illumination at the surface of workstation should be minimum of -
correct answer ✅1000 lm/m^2 or 93 foot candles
, BIPC 620 Exam Questions & Answers
(Grade A+)
A condition that is close to perfect defines what type of condition -
correct answer ✅Target
When inspecting a 22 AWG wire the inspection magnification range
shall be -
correct answer ✅1.5X-3X - Table 1-1
The criteria defined in IPC-620 reflect three product classes , Class
1, 2, 3 -
correct answer ✅Class 1- General Electronic Products
Class 2- Dedicated Service Electronic Products
Class 3- High Performance/ Harsh Environment Electronic Products
If insulation thickness is reduced by more than 20%, the condition
is _1_2_3 -
correct answer ✅Defect for all classes - Chapter 3 - page 3-9
Damaged wires that do not exceed the limits specified in table 3-1
are considered _1_2_3 -
correct answer ✅A1P2P3 so process indicators for 2 and 3 -Page 3-
2
(Grade A+)
Certified IPC Trainer CIT and Certified IPC Specialist certifications
expire after how many years -
correct answer ✅2 Years
Master IPC Trainers MIT are authorized to certify -
correct answer ✅CIT and CIS only
A CIT is authorized to certify -
correct answer ✅CIS
If permitted by company policy, a CIT may grant an extension of up
to how many days -
correct answer ✅90 days
What module is required as a pre req. for IPC 620 CIS certification -
correct answer ✅Module 1
CIS retesting may be taken only after a minimum of -
correct answer ✅24 hours
,BIPC 620 Exam Questions & Answers
(Grade A+)
What is the correct order of production status -
correct answer ✅Design, PCB Fabrication, Assemly, Cleaning and
Coating
The tolerance for magnification aid is -
correct answer ✅Plus or Minus 15 (Chapter 1) Page 1-7
The Manufacturer shall (_1_2_3) have a documented calibration
system -
correct answer ✅N1D2D3 - PAGE 1-8
What is a Process Indicator -
correct answer ✅A condition that identifies a characteristics that
does not affect the form fit or function of a product- should be
monitored
Conditions that are not specified as defective or as a process
indicator are considered -
correct answer ✅Acceptable - Page 1-4
Illumination at the surface of workstation should be minimum of -
correct answer ✅1000 lm/m^2 or 93 foot candles
, BIPC 620 Exam Questions & Answers
(Grade A+)
A condition that is close to perfect defines what type of condition -
correct answer ✅Target
When inspecting a 22 AWG wire the inspection magnification range
shall be -
correct answer ✅1.5X-3X - Table 1-1
The criteria defined in IPC-620 reflect three product classes , Class
1, 2, 3 -
correct answer ✅Class 1- General Electronic Products
Class 2- Dedicated Service Electronic Products
Class 3- High Performance/ Harsh Environment Electronic Products
If insulation thickness is reduced by more than 20%, the condition
is _1_2_3 -
correct answer ✅Defect for all classes - Chapter 3 - page 3-9
Damaged wires that do not exceed the limits specified in table 3-1
are considered _1_2_3 -
correct answer ✅A1P2P3 so process indicators for 2 and 3 -Page 3-
2
