Water Distribution Test (2025) comprehensive
questions and verified detailed solutions (
MULTIPLE CHOICES) |100% CORRECT!!
Leave the first rating
Save
Terms in this set (50) Hide definitions
Distribution systems are usually laid a. Loops and/or circular designs
out in which of the following patterns
besides Tree shaped and Grid
designs?
a. Loops and/or circular designs
b. Vertical designs without backflow
prevention devices
c. Horizontal lines that flow into
open ponds then back into a closed
pipe
d. Horizontal lines that flow into
underground sumps then back into a
closed pipe
,Dead ends in a system are usually b. Tree shaped and Grid designs
located on
a. Loops and/or circular designs
b. Tree shaped and Grid designs
c. Oval designs
d. transmission mains
e. Cul de Sac's with return lines
An operator may refer to d. vertical water column height
Piezometric elevation, static head, or
pressure head as
a. horizontal water elevation
b. water pressure from a pump
c. maximum pressure from a fire
hydrant
d. vertical water column height
, A downstream closed sectionalizing a. the water surface elevation from the last point
valve without pressure reducing where the water is open to the atmosphere
valves in the system will have which
of the following pressures placed
upon it?
a. the water surface elevation from
the last point where the water is
open to the atmosphere
b. the back pressures from a
downstream point
c. the downstream booster pump
operation
d. the operation of a fire hydrant
located immediately downstream of
the hydrant
What is the main purpose of a water d. to provide sufficient amount of water to average
storage facility? or equalize the daily demands plus provide
a. to allow storage reserve during minimum pressures to fight fires
wet periods
b. to help maintain adequate
pressures throughout the entire
system
c. to meet needs for fire protection
d. to provide sufficient amount of
water to average or equalize the
daily demands plus provide minimum
pressures to fight fires
Electrical demand in a wiring system c. Watts consumed
is determined by the amount of
a. Ohms in the entire system
b. Voltage a system draws
c. Watts consumed
d. water pressure in the system
questions and verified detailed solutions (
MULTIPLE CHOICES) |100% CORRECT!!
Leave the first rating
Save
Terms in this set (50) Hide definitions
Distribution systems are usually laid a. Loops and/or circular designs
out in which of the following patterns
besides Tree shaped and Grid
designs?
a. Loops and/or circular designs
b. Vertical designs without backflow
prevention devices
c. Horizontal lines that flow into
open ponds then back into a closed
pipe
d. Horizontal lines that flow into
underground sumps then back into a
closed pipe
,Dead ends in a system are usually b. Tree shaped and Grid designs
located on
a. Loops and/or circular designs
b. Tree shaped and Grid designs
c. Oval designs
d. transmission mains
e. Cul de Sac's with return lines
An operator may refer to d. vertical water column height
Piezometric elevation, static head, or
pressure head as
a. horizontal water elevation
b. water pressure from a pump
c. maximum pressure from a fire
hydrant
d. vertical water column height
, A downstream closed sectionalizing a. the water surface elevation from the last point
valve without pressure reducing where the water is open to the atmosphere
valves in the system will have which
of the following pressures placed
upon it?
a. the water surface elevation from
the last point where the water is
open to the atmosphere
b. the back pressures from a
downstream point
c. the downstream booster pump
operation
d. the operation of a fire hydrant
located immediately downstream of
the hydrant
What is the main purpose of a water d. to provide sufficient amount of water to average
storage facility? or equalize the daily demands plus provide
a. to allow storage reserve during minimum pressures to fight fires
wet periods
b. to help maintain adequate
pressures throughout the entire
system
c. to meet needs for fire protection
d. to provide sufficient amount of
water to average or equalize the
daily demands plus provide minimum
pressures to fight fires
Electrical demand in a wiring system c. Watts consumed
is determined by the amount of
a. Ohms in the entire system
b. Voltage a system draws
c. Watts consumed
d. water pressure in the system
