MSSC CLA ACTUAL EXAM PAPER 2026
QUESTIONS WITH ANSWERS GRADED A+
◍ __________ can be very effective because it helps you unlock ideas that you
would have never thought of on your own..
Answer: Brainstorming
◍ Control charts provide __________ to allow manufacturers to analyze
problems on a piece of equipment..
Answer: Historical data
◍ Measurement of product quality attributes can be assisted by performing
__________..
Answer: Daily quality and equipment checks
◍ The length of the part shown in the drawing is __________ inches..
Answer: 9 ¾
◍ Image magnification is used in what type of device?.
Answer: Optical comparator
◍ Which type best describes the line indicated in the graphic?.
Answer: Object Line
◍ The number of views in a drawing __________..
Answer: Is the fewest number that shows all of the features and dimensions
◍ The PDCA cycle was created by
W. Edwards Deming and stands for __________..
Answer: Plan, Do, Check, and Act
◍ Machine time, task time, and quality requirements are information needed to
__________..
Answer: Document each process
,◍ Brainstorming is __________..
Answer: All of the above
◍ Red tags are typically attached to Parts that are __________..
Answer: Scrapped
◍ What is the order of precedence of lines in a drawing?.
Answer: Object, Hidden, Center
◍ Examples of __________ tolerance describe the form and orientation of a
part..
Answer: Profile
◍ Length, width, height, diameter, and hole diameter are all examples of
__________..
Answer: Features of size
◍ An isometric drawing is a type of __________..
Answer: Pictorial drawing
◍ The material that will be used to create the gear is indicated in the part
drawing's title block to be __________..
Answer: Cast iron
◍ Statistical process control (SPC) is used to __________..
Answer: Determine when a process is going to produce bad parts before it
actually does
◍ Electrical equipment should only be worked on __________..
Answer: After someone has inspected and tested the equipment to ensure
that it has been properly de-energized
◍ A sectional view __________..
Answer: All of the above
◍ Two types of variation are __________..
Answer: Common cause and special cause
◍ In a threaded fastener assembly what is designed to protect the threads?.
, Answer: Shank
◍ Which of these requires a computer?.
Answer: CAD
◍ The measuring tool shown is a __________..
Answer: Depth micrometer
◍ Which of the following is necessary for analyzing work processes?.
Answer: Control charts
◍ Examples of charts used for variable data are the X bar and R chart and the
__________..
Answer: Histogram
◍ An engineering change notice (ECN) is used to notify of changes to
__________..
Answer: A product drawing
◍ A good __________ can both increase value to the customer and reduce
product cost..
Answer: Quality assurance system
◍ From a 2 ft x 3 ft piece of stock, theoretically how many 1 ft x 1.5 ft pieces
can be cut?.
Answer: 4
◍ If 4 percent of 1200 production pieces are out of spec, how many are out of
spec?.
Answer: 48
◍ Benchmarking is a __________ tool..
Answer: Process improvement
◍ If the operator __________ he/she should report this to the supervisor
immediately..
Answer: Has quality/ safety related problems
◍ A line stoppage causes an immediate response from a number of specialists
QUESTIONS WITH ANSWERS GRADED A+
◍ __________ can be very effective because it helps you unlock ideas that you
would have never thought of on your own..
Answer: Brainstorming
◍ Control charts provide __________ to allow manufacturers to analyze
problems on a piece of equipment..
Answer: Historical data
◍ Measurement of product quality attributes can be assisted by performing
__________..
Answer: Daily quality and equipment checks
◍ The length of the part shown in the drawing is __________ inches..
Answer: 9 ¾
◍ Image magnification is used in what type of device?.
Answer: Optical comparator
◍ Which type best describes the line indicated in the graphic?.
Answer: Object Line
◍ The number of views in a drawing __________..
Answer: Is the fewest number that shows all of the features and dimensions
◍ The PDCA cycle was created by
W. Edwards Deming and stands for __________..
Answer: Plan, Do, Check, and Act
◍ Machine time, task time, and quality requirements are information needed to
__________..
Answer: Document each process
,◍ Brainstorming is __________..
Answer: All of the above
◍ Red tags are typically attached to Parts that are __________..
Answer: Scrapped
◍ What is the order of precedence of lines in a drawing?.
Answer: Object, Hidden, Center
◍ Examples of __________ tolerance describe the form and orientation of a
part..
Answer: Profile
◍ Length, width, height, diameter, and hole diameter are all examples of
__________..
Answer: Features of size
◍ An isometric drawing is a type of __________..
Answer: Pictorial drawing
◍ The material that will be used to create the gear is indicated in the part
drawing's title block to be __________..
Answer: Cast iron
◍ Statistical process control (SPC) is used to __________..
Answer: Determine when a process is going to produce bad parts before it
actually does
◍ Electrical equipment should only be worked on __________..
Answer: After someone has inspected and tested the equipment to ensure
that it has been properly de-energized
◍ A sectional view __________..
Answer: All of the above
◍ Two types of variation are __________..
Answer: Common cause and special cause
◍ In a threaded fastener assembly what is designed to protect the threads?.
, Answer: Shank
◍ Which of these requires a computer?.
Answer: CAD
◍ The measuring tool shown is a __________..
Answer: Depth micrometer
◍ Which of the following is necessary for analyzing work processes?.
Answer: Control charts
◍ Examples of charts used for variable data are the X bar and R chart and the
__________..
Answer: Histogram
◍ An engineering change notice (ECN) is used to notify of changes to
__________..
Answer: A product drawing
◍ A good __________ can both increase value to the customer and reduce
product cost..
Answer: Quality assurance system
◍ From a 2 ft x 3 ft piece of stock, theoretically how many 1 ft x 1.5 ft pieces
can be cut?.
Answer: 4
◍ If 4 percent of 1200 production pieces are out of spec, how many are out of
spec?.
Answer: 48
◍ Benchmarking is a __________ tool..
Answer: Process improvement
◍ If the operator __________ he/she should report this to the supervisor
immediately..
Answer: Has quality/ safety related problems
◍ A line stoppage causes an immediate response from a number of specialists
