1 of 26
Term
What is the scope of the Quality System manual?
Give this one a try later!
For the performance qualification testing of pressure welders and machine
welding operators in accordance with ASME section IX and the Alberta Safety
Codes Act and Regulations.
This section describes the procedures that will be used by (name of
company) to conduct renewal performance qualification tests of Welders
and Machine Welding Operators in accordance with the Alberta Safety
Codes Act and Regulations and ASME Section IX.
a) Reviewing the qualifications of NDE examiners and their company's written
procedures and ensuring copies of qualifications and procedures are retained
on file.
b) notifying the examiners of NDE requirements.
c) Identifying the welds to be examined.
,d) Reviewing all NDE reports and radiographic film.
e) Ensuring that the radiographs are traceable to the weld coupon.
a) Verify the joint preparation including land and gap
b) Check the position of the test coupons
c) Verify welding machine set-up including voltage/amperage for specific
electrode size.
d) Assess the tack welds for the length and feathering
e) Complete the applicable section of the Welder/Welding Operator
Qualification Record (AB-76A orAB-76B)
f) Monitor the root pass to ensure it is done in the correct position and direction,
and assess the root pass for quality(penetration, fusion, undercut, profile and
spatter)
g) Monitor the hotpass, fill and cap to ensure welding is done in position and
within the prescribed time frame.
Don't know?
, 2 of 26
Definition
a) Review the candidate's qualifications to ensure the candidate has
an Alberta "A" or "B" Pressure Welder's Certificate of Competency, or
Machine Welding Operator's Certificate of Competency.
b) Make a photocopy of the candidate's Certificate of Competency.
c) Select the welding procedure to be used.
d) Fill in the appropriate parts of the Welder/Welding Operator
Qualification Record(AB-76A or AB-76B).
e) Issue a copy of the Examination and Test Procedure (see Exhibit
9.1 for SMAW process) to the candidate.
f) Issue a copy of the Welding Procedure Specification to the
candidate.
g) Assign a set of test coupons to the candidate.
h) Assign a test area to the candidate.
Give this one a try later!
What are the duties of a Welding
What are the Welding Examiners
Examiner in regard to the NDE
duties after the test?
subcontractor?
What are the Welding
What are the Welding Examiners
Examiner duties prior to the
duties during the test?
test?
Don't know?
3 of 26
Term
What is the scope of the Quality System manual?
Give this one a try later!
For the performance qualification testing of pressure welders and machine
welding operators in accordance with ASME section IX and the Alberta Safety
Codes Act and Regulations.
This section describes the procedures that will be used by (name of
company) to conduct renewal performance qualification tests of Welders
and Machine Welding Operators in accordance with the Alberta Safety
Codes Act and Regulations and ASME Section IX.
a) Reviewing the qualifications of NDE examiners and their company's written
procedures and ensuring copies of qualifications and procedures are retained
on file.
b) notifying the examiners of NDE requirements.
c) Identifying the welds to be examined.
,d) Reviewing all NDE reports and radiographic film.
e) Ensuring that the radiographs are traceable to the weld coupon.
a) Verify the joint preparation including land and gap
b) Check the position of the test coupons
c) Verify welding machine set-up including voltage/amperage for specific
electrode size.
d) Assess the tack welds for the length and feathering
e) Complete the applicable section of the Welder/Welding Operator
Qualification Record (AB-76A orAB-76B)
f) Monitor the root pass to ensure it is done in the correct position and direction,
and assess the root pass for quality(penetration, fusion, undercut, profile and
spatter)
g) Monitor the hotpass, fill and cap to ensure welding is done in position and
within the prescribed time frame.
Don't know?
, 2 of 26
Definition
a) Review the candidate's qualifications to ensure the candidate has
an Alberta "A" or "B" Pressure Welder's Certificate of Competency, or
Machine Welding Operator's Certificate of Competency.
b) Make a photocopy of the candidate's Certificate of Competency.
c) Select the welding procedure to be used.
d) Fill in the appropriate parts of the Welder/Welding Operator
Qualification Record(AB-76A or AB-76B).
e) Issue a copy of the Examination and Test Procedure (see Exhibit
9.1 for SMAW process) to the candidate.
f) Issue a copy of the Welding Procedure Specification to the
candidate.
g) Assign a set of test coupons to the candidate.
h) Assign a test area to the candidate.
Give this one a try later!
What are the duties of a Welding
What are the Welding Examiners
Examiner in regard to the NDE
duties after the test?
subcontractor?
What are the Welding
What are the Welding Examiners
Examiner duties prior to the
duties during the test?
test?
Don't know?
3 of 26
