1|Page
ENGINE REPAIR MICHIGAN MECHANIC STUDY GUIDE
|| MOST RECENT EXAM ACTUAL COMPLETE REAL
VERIFIED EXAM QUESTIONS AND CORRECT
ANSWERS (VERIFIED ANSWERS) ALREADY GRADED
A+ | GUARANTEED SUCCESS!! NEWEST EXAM!!!
Before servicing the supplemental restraint system, what
should a technician do as a safety precaution?
A) cut the wires
B) disarm the system
C) probe the wires with a test light
D) remove the airbag - Answer-B) disarm the system
Which of the following is NOT required when replacing a
cylinder head gasket?
A) checking for warpage
B) checking for squareness
C) checking for leakage
D) cleaning the bolt holes - Answer-B) checking for
squareness
,2|Page
Cylinder head gasket failure may be due to all of the
following except:
A) coolant leaks
B) compression leaks
C) oil leaks
D) vacuum leaks - Answer-D) vacuum leaks
Which of the following should be checked before
disassembling the cylinder head?
A) rocket arm alignment
B) OHC cam bore alignment
C) valve spring installed height
D) surface warpage - Answer-C) valve spring installed
height
Internal cracks on a cast iron cylinder head can be located
by which of the following methods:
A) magnetic particle testing
B) pressure testing
C) dye penetrate testing
D) all the above - Answer-D) all the above
, 3|Page
Typical valve guide clearance would be
A) 0.010- 0.020
B) 0.002- 0.005
C) 0.005- 0.010
D) 0.001-0.002 - Answer-D) 0.001-0.002
Valve margin must be at least?
A) 1/8
B) 1/16
C) 1/32
D) 1/64 - Answer-C) 1/32
Umbrella type valve guide seats are installed:
A) before the valve
B) before the spring
C) with the spring compressed
D) on the guide - Answer-B) before the spring
ENGINE REPAIR MICHIGAN MECHANIC STUDY GUIDE
|| MOST RECENT EXAM ACTUAL COMPLETE REAL
VERIFIED EXAM QUESTIONS AND CORRECT
ANSWERS (VERIFIED ANSWERS) ALREADY GRADED
A+ | GUARANTEED SUCCESS!! NEWEST EXAM!!!
Before servicing the supplemental restraint system, what
should a technician do as a safety precaution?
A) cut the wires
B) disarm the system
C) probe the wires with a test light
D) remove the airbag - Answer-B) disarm the system
Which of the following is NOT required when replacing a
cylinder head gasket?
A) checking for warpage
B) checking for squareness
C) checking for leakage
D) cleaning the bolt holes - Answer-B) checking for
squareness
,2|Page
Cylinder head gasket failure may be due to all of the
following except:
A) coolant leaks
B) compression leaks
C) oil leaks
D) vacuum leaks - Answer-D) vacuum leaks
Which of the following should be checked before
disassembling the cylinder head?
A) rocket arm alignment
B) OHC cam bore alignment
C) valve spring installed height
D) surface warpage - Answer-C) valve spring installed
height
Internal cracks on a cast iron cylinder head can be located
by which of the following methods:
A) magnetic particle testing
B) pressure testing
C) dye penetrate testing
D) all the above - Answer-D) all the above
, 3|Page
Typical valve guide clearance would be
A) 0.010- 0.020
B) 0.002- 0.005
C) 0.005- 0.010
D) 0.001-0.002 - Answer-D) 0.001-0.002
Valve margin must be at least?
A) 1/8
B) 1/16
C) 1/32
D) 1/64 - Answer-C) 1/32
Umbrella type valve guide seats are installed:
A) before the valve
B) before the spring
C) with the spring compressed
D) on the guide - Answer-B) before the spring
