BECC MOD 1 TEST Questions with Verified Answers Rated A
What ARE 3 considerations when dealing with electrical a qualified ....... - ANSWER -ELECTRICIAN
burns? - ANSWER -Electrical current may burn a
large area just below the surface
Perform CPR if needed A torque wrench is used to measure the tightness of ... -
Treatment is the same as for a thermal burn ANSWER -FASTENERS
(True/False) Section 300 of the PQS book list infrequent Torque wrenches are considered ....... equipment -
task and abnormal conditions. - ANSWER -TRUE ANSWER -PRECISION
The overall purpose of PQS is to ...... - ANSWER - If a maintenance procedure does not specify a torque
provide a means to qualify ships personnel. sequence, utilize the recommended sequence found in
....... - ANSWER -NTM CHAPER 075
(True/False) PQS provides an effective way to monitor an
individual's qualification progress. - ANSWER - Which document contains maintenance requirements
TRUE pertaining to all equipment in a command? -
ANSWER -PMS MASTER FILE
When can your Final Qualification Page be signed?. -
ANSWER -After all line items have been completed 16. Which portion of the PMS Master File provides the
and signed work center supervisor a ready reference of planned
maintenance requirements.? - ANSWER -WORK
CENTER PMS MANUAL
Vocabulary used in each qualification can be found in the
....... Section of the PQS book. - ANSWER -
FUNDAMENTALS If a planned maintenance action cannot be completed in
accordance with the steps listed on the MRC, the
maintenance man should ....... - ANSWER -STOP
Progress and completed qualifications of each person in AND REPORT TO THE WCS
the division are displayed on/in the ....... -
ANSWER -PROGRESS CHART
What is used to notify personnel that death or injury may
result if the operating procedures and practices are NOT
Who is the final qualification authority? - ANSWER - correctly followed? - ANSWER -Warnings
COMMANDING OFFICER
Which of the following serves as the "Table of Contents"
A five inch outside micrometer will measure objects that for the Work Center PMS manual? - ANSWER -LIST
are ....... inches thick. - ANSWER -4-5IN OF EFFECTIVE PAGES (LOEP)
A Dial indicator may be used to....... - ANSWER - The SYSCOM Control Number assigned for each
ALIGN MACHINERY maintenance requirement listed in a MIP must match the
number on the corresponding - ANSWER -MRC
(maintenance requirement card)
It is NOT safe to operate electrical power tools in areas
where ....... is/are present. - ANSWER -
FLAMMABLE GASES Materials needed to perform the required maintenance are
found on the - ANSWER -FRONT OF THE MRC
Electrical power tools must be inspected prior to issue by
1/4
What ARE 3 considerations when dealing with electrical a qualified ....... - ANSWER -ELECTRICIAN
burns? - ANSWER -Electrical current may burn a
large area just below the surface
Perform CPR if needed A torque wrench is used to measure the tightness of ... -
Treatment is the same as for a thermal burn ANSWER -FASTENERS
(True/False) Section 300 of the PQS book list infrequent Torque wrenches are considered ....... equipment -
task and abnormal conditions. - ANSWER -TRUE ANSWER -PRECISION
The overall purpose of PQS is to ...... - ANSWER - If a maintenance procedure does not specify a torque
provide a means to qualify ships personnel. sequence, utilize the recommended sequence found in
....... - ANSWER -NTM CHAPER 075
(True/False) PQS provides an effective way to monitor an
individual's qualification progress. - ANSWER - Which document contains maintenance requirements
TRUE pertaining to all equipment in a command? -
ANSWER -PMS MASTER FILE
When can your Final Qualification Page be signed?. -
ANSWER -After all line items have been completed 16. Which portion of the PMS Master File provides the
and signed work center supervisor a ready reference of planned
maintenance requirements.? - ANSWER -WORK
CENTER PMS MANUAL
Vocabulary used in each qualification can be found in the
....... Section of the PQS book. - ANSWER -
FUNDAMENTALS If a planned maintenance action cannot be completed in
accordance with the steps listed on the MRC, the
maintenance man should ....... - ANSWER -STOP
Progress and completed qualifications of each person in AND REPORT TO THE WCS
the division are displayed on/in the ....... -
ANSWER -PROGRESS CHART
What is used to notify personnel that death or injury may
result if the operating procedures and practices are NOT
Who is the final qualification authority? - ANSWER - correctly followed? - ANSWER -Warnings
COMMANDING OFFICER
Which of the following serves as the "Table of Contents"
A five inch outside micrometer will measure objects that for the Work Center PMS manual? - ANSWER -LIST
are ....... inches thick. - ANSWER -4-5IN OF EFFECTIVE PAGES (LOEP)
A Dial indicator may be used to....... - ANSWER - The SYSCOM Control Number assigned for each
ALIGN MACHINERY maintenance requirement listed in a MIP must match the
number on the corresponding - ANSWER -MRC
(maintenance requirement card)
It is NOT safe to operate electrical power tools in areas
where ....... is/are present. - ANSWER -
FLAMMABLE GASES Materials needed to perform the required maintenance are
found on the - ANSWER -FRONT OF THE MRC
Electrical power tools must be inspected prior to issue by
1/4
