Mechanics Exam - 2026 | Verified Answers & Complete Study Guide forPage
Exam1 Prep,
of 99
Mechanics Exam.pdf, including verified answers and complete solutions.
Mechanics Exam
Question:
1 gallon is how many cubic inches?
ANSWER ✔ 231
Question:
A Force of 5000 lbs is applied to a plunger with an area of 25 sq inches.
What is the system pressure?
ANSWER ✔ 200 psi. (5000 lbs/ 25 sq inches = 200 psi
Question:
A motor needs a sleeve bearing replaced. What type of bearing will you
need? - ANSWER ✔ Friction Bearing (420)
Question:
ADA height for a new Hall Fixture? - ANSWER ✔ 42" to center of fixture
Page 1 of 99 1 Mechanics Exam.pdf
,Mechanics Exam - 2026 | Verified Answers & Complete Study Guide forPage
Exam2 Prep,
of 99
Mechanics Exam.pdf, including verified answers and complete solutions.
Question:
How do you handle a coworker who shows up to work intoxicated? -
ANSWER ✔ Speak to the MIC, Union BA or call your Supervisor.
Question:
If changes need to be made during construction, who do you inform? -
ANSWER ✔ Mechanic In Charge
Question:
If there is high screeching, what should you check? - ANSWER ✔ SCR
drive motor bushing
Question:
In Bi-Parting doors, what gap is allowed before Gate switch is opened? -
ANSWER ✔ 3/4" Max
Question:
In what section of the NEC is Elevator, Escalator, Dumbwaiter and Moving
Walks found? - ANSWER ✔ 620
Page 2 of 99 2 Mechanics Exam.pdf
,Mechanics Exam - 2026 | Verified Answers & Complete Study Guide forPage
Exam3 Prep,
of 99
Mechanics Exam.pdf, including verified answers and complete solutions.
Question:
On a Ward-Leonard circuit, the brake is set but the motor is trying to slip
through the brake. What circuit is the issue? - ANSWER ✔ Suicide circuit
(425)
Question
: SCRs are good for what? - ANSWER ✔ They are quieter and cause less
vibration than an MG Set.
Question:
Time constant question on test? - ANSWER ✔ 45 seconds
Question: What amount of Crosby's do you use on 1/2" rope? - ANSWER
✔3
Question:
What are the most common features of Load Weigh? - ANSWER ✔ To
control the Generator field and express operation.
Question: What do U grooves need? - ANSWER ✔ Double Wrap
Page 3 of 99 3 Mechanics Exam.pdf
, Mechanics Exam - 2026 | Verified Answers & Complete Study Guide forPage
Exam4 Prep,
of 99
Mechanics Exam.pdf, including verified answers and complete solutions.
Question: What do you hold a machine beam down with? - ANSWER ✔
Tie downs
Question: What is going on if you add power to a generator but motor
doesn't gain more speed? - ANSWER ✔ Generator is Saturated.
Question: What is Relief set at? - ANSWER ✔ 150%
Question: What is required on the Cartop by ASME? - ANSWER ✔
Inspection Station, Light, Duplex receptacle.
Question: What is the conversion formula when measuring Inch to MM? -
ANSWER ✔ 25.4 Inch to MM (.03937)
2.54 Inch to CM (.3937)
Question: What is the conversion from Kilograms to Lbs? - ANSWER ✔ 1
Kilogram = 2.2 lbs
Page 4 of 99 4 Mechanics Exam.pdf
Exam1 Prep,
of 99
Mechanics Exam.pdf, including verified answers and complete solutions.
Mechanics Exam
Question:
1 gallon is how many cubic inches?
ANSWER ✔ 231
Question:
A Force of 5000 lbs is applied to a plunger with an area of 25 sq inches.
What is the system pressure?
ANSWER ✔ 200 psi. (5000 lbs/ 25 sq inches = 200 psi
Question:
A motor needs a sleeve bearing replaced. What type of bearing will you
need? - ANSWER ✔ Friction Bearing (420)
Question:
ADA height for a new Hall Fixture? - ANSWER ✔ 42" to center of fixture
Page 1 of 99 1 Mechanics Exam.pdf
,Mechanics Exam - 2026 | Verified Answers & Complete Study Guide forPage
Exam2 Prep,
of 99
Mechanics Exam.pdf, including verified answers and complete solutions.
Question:
How do you handle a coworker who shows up to work intoxicated? -
ANSWER ✔ Speak to the MIC, Union BA or call your Supervisor.
Question:
If changes need to be made during construction, who do you inform? -
ANSWER ✔ Mechanic In Charge
Question:
If there is high screeching, what should you check? - ANSWER ✔ SCR
drive motor bushing
Question:
In Bi-Parting doors, what gap is allowed before Gate switch is opened? -
ANSWER ✔ 3/4" Max
Question:
In what section of the NEC is Elevator, Escalator, Dumbwaiter and Moving
Walks found? - ANSWER ✔ 620
Page 2 of 99 2 Mechanics Exam.pdf
,Mechanics Exam - 2026 | Verified Answers & Complete Study Guide forPage
Exam3 Prep,
of 99
Mechanics Exam.pdf, including verified answers and complete solutions.
Question:
On a Ward-Leonard circuit, the brake is set but the motor is trying to slip
through the brake. What circuit is the issue? - ANSWER ✔ Suicide circuit
(425)
Question
: SCRs are good for what? - ANSWER ✔ They are quieter and cause less
vibration than an MG Set.
Question:
Time constant question on test? - ANSWER ✔ 45 seconds
Question: What amount of Crosby's do you use on 1/2" rope? - ANSWER
✔3
Question:
What are the most common features of Load Weigh? - ANSWER ✔ To
control the Generator field and express operation.
Question: What do U grooves need? - ANSWER ✔ Double Wrap
Page 3 of 99 3 Mechanics Exam.pdf
, Mechanics Exam - 2026 | Verified Answers & Complete Study Guide forPage
Exam4 Prep,
of 99
Mechanics Exam.pdf, including verified answers and complete solutions.
Question: What do you hold a machine beam down with? - ANSWER ✔
Tie downs
Question: What is going on if you add power to a generator but motor
doesn't gain more speed? - ANSWER ✔ Generator is Saturated.
Question: What is Relief set at? - ANSWER ✔ 150%
Question: What is required on the Cartop by ASME? - ANSWER ✔
Inspection Station, Light, Duplex receptacle.
Question: What is the conversion formula when measuring Inch to MM? -
ANSWER ✔ 25.4 Inch to MM (.03937)
2.54 Inch to CM (.3937)
Question: What is the conversion from Kilograms to Lbs? - ANSWER ✔ 1
Kilogram = 2.2 lbs
Page 4 of 99 4 Mechanics Exam.pdf
