ARIZONA CR34 PAINTING AND WALL
COVERING ACTUAL EXAM REVIEW SHEET
VERIFIED QUESTIONS AND ACCURATE
ANSWERS GRADED A+
⩥ For a low voltage configuration, the conductors to use should never be
smaller than?
Answer: 12 AWG copper (or equivalent)
⩥ For a low voltage configuration, the conductors to use for appliance
branch circuits that supply more than one appliance should never be
smaller than?
Answer: 10 AWG copper (or equivalent)
⩥ For a low voltage configuration, standard lampholders with a rating
less than _______ watts should not be used.
Answer: 660 W
⩥ Even in a low voltage configuration, the receptacles of less than
______ -ampere rating should not be used in kitchens where portable
appliances will be deployed.
Answer: 20 -ampere
,⩥ Even in a low voltage configuration, the receptacles of less than
_________ -ampere rating should not be used in laundries where
portable appliances will be deployed.
Answer: 20 -ampere
⩥ Even in a low voltage configuration, cables should be supported by?
Answer: The building structure.
⩥ A Class 1 Circuit stays between?
Answer: The load side of the overcurrent device and the connected
equipment.
⩥ Whenever practicable, communications wires and cable should be
located _______ electric light or power conductors.
Answer: Below.
⩥ You should not allow communications wires to be attached to a cross-
arm if?
Answer: the cross-arm carries electric power conductors.
⩥ At the roof, you need to give communications cables a minimum
vertical clearance of _______ feet from the points above which they
pass.
Answer: 8 feet
, ⩥ A class _____ Circuit stays between the load side of a Class 2 power
source and a connected equipment.
Answer: 2 Circuit
⩥ Remote -control circuits for use with safety - control equipment are
considered Class _____ if failure to operate can introduce direct fire of
life hazard.
Answer: 1
⩥ Class 1 power -Limited Circuits should be supplied from a source that
has a rated output of ______ volts or below only.
Answer: 30 volts
⩥ A class ______ circuits always considers safety from a fire initiation
standpoint.
Answer: 2 circuits
⩥ Class 1 Power Sources other than transformers should have protection
from overcurrent devices rated at max ______ of the volt -- ampere
rating of the source divided by the rated voltage.
Answer: 167%
⩥ A Class ______ circuit permits higher voltage than a class 2 circuit.
COVERING ACTUAL EXAM REVIEW SHEET
VERIFIED QUESTIONS AND ACCURATE
ANSWERS GRADED A+
⩥ For a low voltage configuration, the conductors to use should never be
smaller than?
Answer: 12 AWG copper (or equivalent)
⩥ For a low voltage configuration, the conductors to use for appliance
branch circuits that supply more than one appliance should never be
smaller than?
Answer: 10 AWG copper (or equivalent)
⩥ For a low voltage configuration, standard lampholders with a rating
less than _______ watts should not be used.
Answer: 660 W
⩥ Even in a low voltage configuration, the receptacles of less than
______ -ampere rating should not be used in kitchens where portable
appliances will be deployed.
Answer: 20 -ampere
,⩥ Even in a low voltage configuration, the receptacles of less than
_________ -ampere rating should not be used in laundries where
portable appliances will be deployed.
Answer: 20 -ampere
⩥ Even in a low voltage configuration, cables should be supported by?
Answer: The building structure.
⩥ A Class 1 Circuit stays between?
Answer: The load side of the overcurrent device and the connected
equipment.
⩥ Whenever practicable, communications wires and cable should be
located _______ electric light or power conductors.
Answer: Below.
⩥ You should not allow communications wires to be attached to a cross-
arm if?
Answer: the cross-arm carries electric power conductors.
⩥ At the roof, you need to give communications cables a minimum
vertical clearance of _______ feet from the points above which they
pass.
Answer: 8 feet
, ⩥ A class _____ Circuit stays between the load side of a Class 2 power
source and a connected equipment.
Answer: 2 Circuit
⩥ Remote -control circuits for use with safety - control equipment are
considered Class _____ if failure to operate can introduce direct fire of
life hazard.
Answer: 1
⩥ Class 1 power -Limited Circuits should be supplied from a source that
has a rated output of ______ volts or below only.
Answer: 30 volts
⩥ A class ______ circuits always considers safety from a fire initiation
standpoint.
Answer: 2 circuits
⩥ Class 1 Power Sources other than transformers should have protection
from overcurrent devices rated at max ______ of the volt -- ampere
rating of the source divided by the rated voltage.
Answer: 167%
⩥ A Class ______ circuit permits higher voltage than a class 2 circuit.
