NACE CIP 1 CBT EXAM PRACTICE EXAM WITH
ACTUAL QUESTIONS AND 100% VERIFIED ANSWERS
| LATEST 2025/ 2026 UPDATE | GRADED A+ | 100%
SUCCESS
A well written specification requires a surface profile depth defined as?
- correct answer -A range of measurements.
The testing for water soluble ferrous salts is? - correct answer -
Potassium Ferricyanide Test
Solventborne inorganic zinc primer is being applied with airless spray to
complex bride with difficult access for application. The contractor is
having difficulty with hight DFT resulting in mkudcracking. What
application method might be a good alternative? - correct answer -
Conventional Spray
When reporting the wet film thickness from a wet film thickness
comb/gauge (WFT) you report? - correct answer -The last tooth that has
coating on it.
,Adding an incorrect solvent to a coating may cause? - correct answer -
Non drying and non curing.
You are reviewing the documentation for a tank waiting project and
notice there is a conflict between the project specification and the
manufacture's product data sheet on the required DFT of the primer.
The owner is not reachable for clarification. What should be done? -
correct answer -Follow the specification.
You know that you are sensitive to amines, but not polyamides. What
document would you review prior to arriving on the joist to know
whether amines will be used? - correct answer -The contractor's
contract.
The formation of small bowl shaped depressions in the coating find
cause by air trapped in the coating is called? - correct answer -Cratering
,Failure of a plural component to cure is frequently caused by? - correct
answer -Wrong mix ratio(metering)
One of the most common cause of clusters in a coating film is? - correct
answer -Surface Contamination
You have been inspecting a tank repainting project and suspect the
surface was not cleaned properly, but the coating has already been
applied. What should you do? - correct answer -Consult owner for
guidance.
After a cold night, you find that the epoxy amine midcoast applied the
day before has blushed. The optimum (best) resolution when amine
blush is found is to? - correct answer -Consult the coating manufacture.
As in Inspector on a bride painting project, prior to abrasive
blasting,which blasting safety items would you expect to see? - correct
answer -Deadman valve, Connections wired/clipped and Supplied air
hood.
, According to NACE SP0188, the wetted sponge is moved at a maximum
rate of? - correct answer -1 linear foot per second (30cm)
You are on a coating project and notice blisters in a variety of sizes and
irregular shapes. What standard would you use to evaluate the blisters?
- correct answer -ASTM D714
When are NACE International surface preparation standards considered
binding? - correct answer -When specified in the contract documents.
You are performing holiday testing early morning with dew on the pipe.
The reason you may get erroneous indications is cause by? - correct
answer -Telegraphing
Which joint NACE/SSPC abrasive blasting standard states that "Random
staying shall be limited to no more than 33% of each unit surface area"?
- correct answer -NACE No. 3/SSPC SP 6 Commercial Blast Cleaning
ACTUAL QUESTIONS AND 100% VERIFIED ANSWERS
| LATEST 2025/ 2026 UPDATE | GRADED A+ | 100%
SUCCESS
A well written specification requires a surface profile depth defined as?
- correct answer -A range of measurements.
The testing for water soluble ferrous salts is? - correct answer -
Potassium Ferricyanide Test
Solventborne inorganic zinc primer is being applied with airless spray to
complex bride with difficult access for application. The contractor is
having difficulty with hight DFT resulting in mkudcracking. What
application method might be a good alternative? - correct answer -
Conventional Spray
When reporting the wet film thickness from a wet film thickness
comb/gauge (WFT) you report? - correct answer -The last tooth that has
coating on it.
,Adding an incorrect solvent to a coating may cause? - correct answer -
Non drying and non curing.
You are reviewing the documentation for a tank waiting project and
notice there is a conflict between the project specification and the
manufacture's product data sheet on the required DFT of the primer.
The owner is not reachable for clarification. What should be done? -
correct answer -Follow the specification.
You know that you are sensitive to amines, but not polyamides. What
document would you review prior to arriving on the joist to know
whether amines will be used? - correct answer -The contractor's
contract.
The formation of small bowl shaped depressions in the coating find
cause by air trapped in the coating is called? - correct answer -Cratering
,Failure of a plural component to cure is frequently caused by? - correct
answer -Wrong mix ratio(metering)
One of the most common cause of clusters in a coating film is? - correct
answer -Surface Contamination
You have been inspecting a tank repainting project and suspect the
surface was not cleaned properly, but the coating has already been
applied. What should you do? - correct answer -Consult owner for
guidance.
After a cold night, you find that the epoxy amine midcoast applied the
day before has blushed. The optimum (best) resolution when amine
blush is found is to? - correct answer -Consult the coating manufacture.
As in Inspector on a bride painting project, prior to abrasive
blasting,which blasting safety items would you expect to see? - correct
answer -Deadman valve, Connections wired/clipped and Supplied air
hood.
, According to NACE SP0188, the wetted sponge is moved at a maximum
rate of? - correct answer -1 linear foot per second (30cm)
You are on a coating project and notice blisters in a variety of sizes and
irregular shapes. What standard would you use to evaluate the blisters?
- correct answer -ASTM D714
When are NACE International surface preparation standards considered
binding? - correct answer -When specified in the contract documents.
You are performing holiday testing early morning with dew on the pipe.
The reason you may get erroneous indications is cause by? - correct
answer -Telegraphing
Which joint NACE/SSPC abrasive blasting standard states that "Random
staying shall be limited to no more than 33% of each unit surface area"?
- correct answer -NACE No. 3/SSPC SP 6 Commercial Blast Cleaning
