NEIEP 800 Final Exam – 2025–2026 – Elevator Industry Certification Prep Accurate Real Exam Questions and Verified Correct Answers – JUST RELEASED

NEIEP 800 Final Exam – 2025–2026 – Elevator Industry Certification Prep Accurate Real Exam Questions and Verified Correct Answers – JUST RELEASED The _____ _____ short radius spiral is a type of short radius spiral. - ANSWER double 90 The capacity of a chairlift shall not exceed two persons. The rated load shall not be less than _____ lbs for a one seat lift and not less than _____ lbs for a two seat lift. The speed shall not exceed _____ fpm. - ANSWER -250, 400, 40 (True/False) With platform lifts, codes require a handrail between 1 and 3 inches in diameter, 1 1/2 inches minimum from the wall and 34 to 38 inches above the stair tread nosing. - ANSWER -True Per code, where the actuation of the safeties is by a governor, the safety shall be set at a maximum speed of _____ fpm - ANSWER -75 With platform lifts, the _____ is referring to the space occupied by the lifts' travel whether it is enclosed, partially enclosed or open construction. - ANSWER Runway Routine tests and inspections are to be made every _____ months for LULA's in buildings other than private residences and every _____ for private residences. - ANSWER -6, year What is the minimum height of a barricade in place around an open wellway? - ANSWER -42" What is the maximum angle of inclination for moving walks? - ANSWER -12 degrees The major advantage of a hydraulic elevator is that it __________ _________ building structural support. - ANSWER -requires less What would be the effect of increasing the size of the oil line if all other elements in a hydraulic elevator system remain the same? - ANSWER -Rate of flow is increased A __________ __________ is used to check a jack hole for plumb. - ANSWER spider bob What is the operating pressure of a hydraulic elevator with a gross weight of 1500 pounds and a plunger area of 15 square inches? - ANSWER -100 psi One gallon equals __________ cubic inches. - ANSWER -231 Why is it important to follow a welding procedure using a sequence of short welds on opposite sides of the cylinder? - ANSWER -To prevent warping the cylinder If all other elements in a hydraulic elevator system remain the same, what would be the effect of reducing the diameter of the plunger? - ANSWER -Higher system pressure How do you prevent rusting of the plunger if the jack unit is installed in the well hole long before the elevator will be completed? - ANSWER -Fill it with oil (True/False)The pressure relief valve is operated electronically. - ANSWER -False What prevents the plunger from leaving the cylinder? - ANSWER -The stop ring The advantage of wye-delta starting is what? - ANSWER -Starting current is lower A __________ cushions pulsations in the oil caused by the pump. - ANSWER silencer You can lower a hydraulic elevator without power by using the __________ __________ __________. - ANSWER -manual lowering valve The __________ __________ assembly supports the platform of a hydraulic elevator. - ANSWER -bolster channel It is necessary to run a ground wire to the car sling of a hydraulic elevator to prevent what? - ANSWER -electrical shock What condition will trip a GFCI? - ANSWER -If a supply lead is shorted to ground When using a beam clamp, a good rule of thumb is to never load the lower flange to more than __________ % of the load which could be handled by the full area of the beam. - ANSWER -50 1 lb equals how many Kg? - ANSWER -.4536 2,000 Kg = __________ lbs - ANSWER -4,409 What is the best rigging equipment to use for controlling horizontal movement of the escalator as it is being lifted into position in the wellway? - ANSWER -lever hoist What is the most common shackle used? - ANSWER -Screw pin bow type The angle of inclination can __________ 30 degrees by a maximum of __________ degrees at the installation site. - ANSWER -exceed; 1 The maximum distance between anti-slide devices on an escalator is what? - ANSWER -6' What happens if a step of an escalator drops more than 1/8"? - ANSWER -The escalator stops automatically Combplate teeth must be set to ensure the teeth are always __________ the __________ surface of the treads. - ANSWER -below; upper What is the maximum allowable gap between the skirt panels on an escalator and the adjacent step tread? - ANSWER -3/16" Where is the tensioning device located in a belted moving walkway? - ANSWER Tail end Moving walk overspeed switches must switch at no more than __________% the rated speed. - ANSWER -20 What is the maximum rise of a LULA? - ANSWER -25'