NIMS Lathe Study Guide – Questions With
Applicable Solutions
Save
Practice questions for this set
Learn 1 /7 Study with Learn
509 RPM
Choose an answer
What is the RPM needed to drill a .750"
hole in mild steel with a cutting Which of the following statements
1 2
speed of 100 SFM on 3.50" diameter best defines cutting speed
stock (use 3.82 for the constant)?
Identify the proper formula for
Which of the following statements
3 4 determining the RPM for a turning
does not describe a universal chuck
operation
Don't know?
Terms in this set (41)
Cutting speed is based on the distance the work moves
Which of the following past the
statements best defines tool based on the number of feet that passes the tool in
cutting speed one minute
and is given in surface feet per minute
, Which of the following The machine movement that causes a tool to cut into or
statements best defines along the
feed? surface of a work piece
When calculating the RPM The diameter of the work piece
for a turning operation, the
machinist uses
_________ instead of the
diameter of the tool.
What is the RPM needed to 509 RPM
drill a .750" hole in mild
steel with a cutting
speed of 100 SFM on 3.50"
diameter stock (use 3.82 for
the constant)?
A part is being turned at 5.30 minutes
250 RPM with a feed rate of
.008 inches per
revolution. How long will it
take to make one pass if
the part is 10.625
inches long?
Identify the proper formula (CS • 3.82) / D
for determining the RPM
for a turning operation
How is a feed rate Inches per revolution
designated on a lathe?
The feed rate is at .008 IPR. 450 RPM
How many RPM will it take
to move the tool a
distance of 3.600 inches in
a minute?
Which of the following T = L / (fN)
formulas is the correct
formula for determining the
time to make one cut
across a given distance?
Applicable Solutions
Save
Practice questions for this set
Learn 1 /7 Study with Learn
509 RPM
Choose an answer
What is the RPM needed to drill a .750"
hole in mild steel with a cutting Which of the following statements
1 2
speed of 100 SFM on 3.50" diameter best defines cutting speed
stock (use 3.82 for the constant)?
Identify the proper formula for
Which of the following statements
3 4 determining the RPM for a turning
does not describe a universal chuck
operation
Don't know?
Terms in this set (41)
Cutting speed is based on the distance the work moves
Which of the following past the
statements best defines tool based on the number of feet that passes the tool in
cutting speed one minute
and is given in surface feet per minute
, Which of the following The machine movement that causes a tool to cut into or
statements best defines along the
feed? surface of a work piece
When calculating the RPM The diameter of the work piece
for a turning operation, the
machinist uses
_________ instead of the
diameter of the tool.
What is the RPM needed to 509 RPM
drill a .750" hole in mild
steel with a cutting
speed of 100 SFM on 3.50"
diameter stock (use 3.82 for
the constant)?
A part is being turned at 5.30 minutes
250 RPM with a feed rate of
.008 inches per
revolution. How long will it
take to make one pass if
the part is 10.625
inches long?
Identify the proper formula (CS • 3.82) / D
for determining the RPM
for a turning operation
How is a feed rate Inches per revolution
designated on a lathe?
The feed rate is at .008 IPR. 450 RPM
How many RPM will it take
to move the tool a
distance of 3.600 inches in
a minute?
Which of the following T = L / (fN)
formulas is the correct
formula for determining the
time to make one cut
across a given distance?
