Surface Mining Operations Practice Test –
100 Questions With Rationales
1–20
1. What is the primary purpose of a surface mine safety plan?
A. To increase mine production
B. To reduce fuel consumption
C. To identify and control workplace hazards
D. To evaluate employee performance
Rationale: A safety plan outlines hazards and controls to protect
workers.
2. Which federal agency regulates surface mining safety in the U.S.?
A. OSHA
B. MSHA
C. EPA
D. DOT
Rationale: MSHA regulates mining safety, including surface
operations.
3. The most common cause of fatal accidents in surface mines is:
A. Wildlife intrusion
B. Mobile equipment incidents
C. Blasting fumes
D. Conveyor belt jams
Rationale: Mobile equipment collisions and rollovers are the
leading causes.
,4. Before beginning a shift, miners must complete:
A. A personal checklist
B. A training review
C. A pre-shift inspection
D. An exam
Rationale: Pre-shift inspections detect unsafe conditions before
work begins.
5. The “three-point contact” rule applies to:
A. First-aid response
B. Mounting and dismounting equipment
C. Hazard communication meetings
D. Lockout procedures
Rationale: Three points of contact prevent falls when climbing on
equipment.
6. Bench stability is maintained by controlling:
A. Groundwater temperature
B. Slope angle and bench width
C. Equipment horsepower
D. Wind direction
Rationale: Slope geometry is key to preventing bench failures.
7. A “highwall” refers to:
A. A conveyor system
B. The unexcavated face of a surface mine
C. A stockpile boundary
D. A road berm
Rationale: Highwalls are exposed rock faces created by surface
mining.
8. Water accumulation in pits increases the risk of:
A. Fuel contamination
, B. Slope failure and equipment entrapment
C. Increased ore grade
D. Electrical efficiency
Rationale: Water can weaken slopes and trap machinery.
9. Which type of PPE is required where flying rock fragments are
possible?
A. Hearing protection
B. Respiratory mask
C. Safety goggles or face shield
D. Rubber boots
Rationale: Eye/face protection prevents injury from projectiles.
10. Blasting operations must be conducted by:
A. Any miner
B. Equipment operators
C. Supervisors
D. Certified and authorized blasters
Rationale: Only certified blasters may handle explosives.
11. A berm along a haul road serves to:
A. Prevent dust
B. Keep equipment from driving over edges
C. Mark survey boundaries
D. Direct wildlife movement
Rationale: Berms act as protective barriers.
12. Contact with overhead power lines can be prevented by:
A. Assigning extra supervisors
B. Maintaining safe approach distances
C. Increasing equipment speed
D. Using smaller equipment
Rationale: Safe distances reduce risk of electrocution.
100 Questions With Rationales
1–20
1. What is the primary purpose of a surface mine safety plan?
A. To increase mine production
B. To reduce fuel consumption
C. To identify and control workplace hazards
D. To evaluate employee performance
Rationale: A safety plan outlines hazards and controls to protect
workers.
2. Which federal agency regulates surface mining safety in the U.S.?
A. OSHA
B. MSHA
C. EPA
D. DOT
Rationale: MSHA regulates mining safety, including surface
operations.
3. The most common cause of fatal accidents in surface mines is:
A. Wildlife intrusion
B. Mobile equipment incidents
C. Blasting fumes
D. Conveyor belt jams
Rationale: Mobile equipment collisions and rollovers are the
leading causes.
,4. Before beginning a shift, miners must complete:
A. A personal checklist
B. A training review
C. A pre-shift inspection
D. An exam
Rationale: Pre-shift inspections detect unsafe conditions before
work begins.
5. The “three-point contact” rule applies to:
A. First-aid response
B. Mounting and dismounting equipment
C. Hazard communication meetings
D. Lockout procedures
Rationale: Three points of contact prevent falls when climbing on
equipment.
6. Bench stability is maintained by controlling:
A. Groundwater temperature
B. Slope angle and bench width
C. Equipment horsepower
D. Wind direction
Rationale: Slope geometry is key to preventing bench failures.
7. A “highwall” refers to:
A. A conveyor system
B. The unexcavated face of a surface mine
C. A stockpile boundary
D. A road berm
Rationale: Highwalls are exposed rock faces created by surface
mining.
8. Water accumulation in pits increases the risk of:
A. Fuel contamination
, B. Slope failure and equipment entrapment
C. Increased ore grade
D. Electrical efficiency
Rationale: Water can weaken slopes and trap machinery.
9. Which type of PPE is required where flying rock fragments are
possible?
A. Hearing protection
B. Respiratory mask
C. Safety goggles or face shield
D. Rubber boots
Rationale: Eye/face protection prevents injury from projectiles.
10. Blasting operations must be conducted by:
A. Any miner
B. Equipment operators
C. Supervisors
D. Certified and authorized blasters
Rationale: Only certified blasters may handle explosives.
11. A berm along a haul road serves to:
A. Prevent dust
B. Keep equipment from driving over edges
C. Mark survey boundaries
D. Direct wildlife movement
Rationale: Berms act as protective barriers.
12. Contact with overhead power lines can be prevented by:
A. Assigning extra supervisors
B. Maintaining safe approach distances
C. Increasing equipment speed
D. Using smaller equipment
Rationale: Safe distances reduce risk of electrocution.