DPWH Project Engineer Exam
2026: Questions, Answers, and Tips
Ace your upcoming DPWH Project Engineer examination with our targeted 2026
reviewer. This comprehensive guide is specifically designed for Filipino civil engineering
students and graduates, featuring a curated set of practice questions that mirror the
actual test format. Get instant access to essential topics like Materials Engineering,
Construction Methods, Project Management, and DPWH Standard Specifications. DPWH
Exam Reviewer, DPWH Project Engineer Exam, Civil Service Exam Reviewer, DPWH
Practice Test, Civil Engineering Board Exam Reviewer
If the project topography does not conform with the approved plan,
what should be immediately submitted for approval by the project
engineer?
as-staked survey/plan
The list of deficiencies to be corrected that is prepared at the final
inspection is sometimes referred to as:
Punchlist
Settlement of right of way should be done?
before the construction work
Which of the following is not a quality test for cement?
California Bearing Ratio (CBR)
Per program of work, the estimated volume of Item 201 materials is
7,500 cu.m. How many Grading and Plasticity tests are require based
on the DPWH minimum testing requirement?
5
,Item 201 materials with CBR value of 75% (which is 5% less than the
minimum requirement) can still be used in the design of a concrete
pavement provided that the following are considered except one:
the foundation contains unsuitable materials
Your total approved accomplishment on a project including those to be
covered by an Extra work is equivalent to 75% but only 65% is covered
under the approved original contract. Up to what level of progress
billing would you allow?
up to the documented value not more than 65%
For bridge and highway projects which of the following hydrologic data
is the most important?
Maximum flood height
In hydrologic survey, sounding points should be made at maximum
interval of:
20 m
A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, its water
content is?
40%
A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, the void ratio
is?
1.1
A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, the porosity
is?
0.524
A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, the wet
density (g/ml) is?
1.83
,A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, the dry
density (g/ml) is?
1.30
Of the following soil, the poorest rated for subgrade is?
A-7
A soil with Group Index of 15 is better than that with:
Group Index > 15
The consistency limits of soils are determined on fractions passing:
Sieve #40 (0.425mm)
The thickest pavement structure could be found on subgrade with CBR
value of:
10
The height of fall of the rammer used to determine the moisture density
relation of soil in the T-180 procedure is?
457mm
Is a heavy monolithic gravity structure consisting of wire baskets filled
with coarse non-degradable rock.
Gabion
Admixtures are used to ___________.
(a) Improve workability
(b) Increase strength
(c) Retard initial setting
All of the above
What will improve if water cement ratio is lowered?
(a) Compressive Strength
(b) Flexural Strength
(c) Bond Strength
All of the above
Concrete specimen molded in a 6"x6''x21" beam mold should be
rodded:
63 times per layer
Quality Tests of concrete coarse aggregate sample requires:
, Abrasion and Stability Test
Concrete fine aggregate should be tested for:
None of the preceedings
Greatest net water is required in a concrete mix with ______ aggregate.
very fine
Slump test could be used to detect:
increase in water
Angular coarse aggregate will require more _______ per unit volume of
concrete.
water and sand
Paving concrete will need less ______ than that of structural concrete.
water and sand
Maintaining the water cement ratio, the concrete containing _____
maximum size aggregate will develop the highest strength.
2 inches
If the concrete beam specimen is ruptured during test outside the
middle third, but within 5% of the span length, the formula to be used in
computing the stress is:
PL/bd^2
Concrete cylinder sample should be molded in ____equal layers.
3 (three)
In molding concrete cylinder specimen, each layer should be rodded
___ times.
25 (twenty five)
The fineness modulus is highest for:
very fine sand
Concrete mix should be in place ____ after the cement is added into the
aggregates and water.
90 minutes
The basic type of manufactured asphalt is:
asphalt cement
2026: Questions, Answers, and Tips
Ace your upcoming DPWH Project Engineer examination with our targeted 2026
reviewer. This comprehensive guide is specifically designed for Filipino civil engineering
students and graduates, featuring a curated set of practice questions that mirror the
actual test format. Get instant access to essential topics like Materials Engineering,
Construction Methods, Project Management, and DPWH Standard Specifications. DPWH
Exam Reviewer, DPWH Project Engineer Exam, Civil Service Exam Reviewer, DPWH
Practice Test, Civil Engineering Board Exam Reviewer
If the project topography does not conform with the approved plan,
what should be immediately submitted for approval by the project
engineer?
as-staked survey/plan
The list of deficiencies to be corrected that is prepared at the final
inspection is sometimes referred to as:
Punchlist
Settlement of right of way should be done?
before the construction work
Which of the following is not a quality test for cement?
California Bearing Ratio (CBR)
Per program of work, the estimated volume of Item 201 materials is
7,500 cu.m. How many Grading and Plasticity tests are require based
on the DPWH minimum testing requirement?
5
,Item 201 materials with CBR value of 75% (which is 5% less than the
minimum requirement) can still be used in the design of a concrete
pavement provided that the following are considered except one:
the foundation contains unsuitable materials
Your total approved accomplishment on a project including those to be
covered by an Extra work is equivalent to 75% but only 65% is covered
under the approved original contract. Up to what level of progress
billing would you allow?
up to the documented value not more than 65%
For bridge and highway projects which of the following hydrologic data
is the most important?
Maximum flood height
In hydrologic survey, sounding points should be made at maximum
interval of:
20 m
A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, its water
content is?
40%
A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, the void ratio
is?
1.1
A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, the porosity
is?
0.524
A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, the wet
density (g/ml) is?
1.83
,A sample of saturated clay has a mass of 102.8 g. After you oven drying,
the same soil weighs 73.4 g. If the specific gravity is 2.74, the dry
density (g/ml) is?
1.30
Of the following soil, the poorest rated for subgrade is?
A-7
A soil with Group Index of 15 is better than that with:
Group Index > 15
The consistency limits of soils are determined on fractions passing:
Sieve #40 (0.425mm)
The thickest pavement structure could be found on subgrade with CBR
value of:
10
The height of fall of the rammer used to determine the moisture density
relation of soil in the T-180 procedure is?
457mm
Is a heavy monolithic gravity structure consisting of wire baskets filled
with coarse non-degradable rock.
Gabion
Admixtures are used to ___________.
(a) Improve workability
(b) Increase strength
(c) Retard initial setting
All of the above
What will improve if water cement ratio is lowered?
(a) Compressive Strength
(b) Flexural Strength
(c) Bond Strength
All of the above
Concrete specimen molded in a 6"x6''x21" beam mold should be
rodded:
63 times per layer
Quality Tests of concrete coarse aggregate sample requires:
, Abrasion and Stability Test
Concrete fine aggregate should be tested for:
None of the preceedings
Greatest net water is required in a concrete mix with ______ aggregate.
very fine
Slump test could be used to detect:
increase in water
Angular coarse aggregate will require more _______ per unit volume of
concrete.
water and sand
Paving concrete will need less ______ than that of structural concrete.
water and sand
Maintaining the water cement ratio, the concrete containing _____
maximum size aggregate will develop the highest strength.
2 inches
If the concrete beam specimen is ruptured during test outside the
middle third, but within 5% of the span length, the formula to be used in
computing the stress is:
PL/bd^2
Concrete cylinder sample should be molded in ____equal layers.
3 (three)
In molding concrete cylinder specimen, each layer should be rodded
___ times.
25 (twenty five)
The fineness modulus is highest for:
very fine sand
Concrete mix should be in place ____ after the cement is added into the
aggregates and water.
90 minutes
The basic type of manufactured asphalt is:
asphalt cement
