STEERING AND SUSPENSION TEST
CORRECT 100%
A customer complains that the steering lacks power assist all the time. Tech a says
that the power steering pump drive belt could be slipping or loose. Tech b says that
worn outer tie rod ends could be the cause. Who is correct? - ANSWERTech A
Defective wheel bearings usually sound like a? - ANSWERGrowl, rumble, snow tires
A defective outer CV joint will usually make a clicking noise when? - ANSWERWhile
turning and moving
The proper lubricant usually specified for use in a differential is? - ANSWERSAE
80w-90 GL5
A vehicle owner complained that a severe vibration was felt throughout the entire
vehicle only during rapid acceleration from stop and up to about 20 mph. The most
likely cause is? - ANSWERIn equal drive shaft working angles
To remove a c-clip axle what step does not need to be done? - ANSWERRemove
the axle flange bolts/nuts
A front wheel drive vehicle pulls towards the right during hard acceleration. The most
likely cause is? - ANSWERNormal torque steer
When replacing a rubber-bonded socket the rod end, the tech should be sure to? -
ANSWERInstall and tighten the replacement with the front wheels in the straight
ahead position
Whenever installing a tire on a rim, do not exceed - ANSWER40psi
Two technicians are discussing mounting a tire on a wheel. Tech a says that for best
balance, the tire should be match mounted. Tech b says that silicone spray should
be used to lubricants the tire bend. Which is correct? - ANSWERTech A
Technician A says that radial tires should only be rotated front to rear, never side to
side. Tech b says that vehicle manufacturers usually recommend radial tires should
be rotated using the modified x method. Which is correct? - ANSWERTech b
For a tire that has excessive radial runout, tech a says that it should be broken down
on a tire changing machine and then rotated 180 degrees on the wheel and retested.
Tech b says that the tire should be replaced. Which tech is correct? - ANSWERTech
a
CORRECT 100%
A customer complains that the steering lacks power assist all the time. Tech a says
that the power steering pump drive belt could be slipping or loose. Tech b says that
worn outer tie rod ends could be the cause. Who is correct? - ANSWERTech A
Defective wheel bearings usually sound like a? - ANSWERGrowl, rumble, snow tires
A defective outer CV joint will usually make a clicking noise when? - ANSWERWhile
turning and moving
The proper lubricant usually specified for use in a differential is? - ANSWERSAE
80w-90 GL5
A vehicle owner complained that a severe vibration was felt throughout the entire
vehicle only during rapid acceleration from stop and up to about 20 mph. The most
likely cause is? - ANSWERIn equal drive shaft working angles
To remove a c-clip axle what step does not need to be done? - ANSWERRemove
the axle flange bolts/nuts
A front wheel drive vehicle pulls towards the right during hard acceleration. The most
likely cause is? - ANSWERNormal torque steer
When replacing a rubber-bonded socket the rod end, the tech should be sure to? -
ANSWERInstall and tighten the replacement with the front wheels in the straight
ahead position
Whenever installing a tire on a rim, do not exceed - ANSWER40psi
Two technicians are discussing mounting a tire on a wheel. Tech a says that for best
balance, the tire should be match mounted. Tech b says that silicone spray should
be used to lubricants the tire bend. Which is correct? - ANSWERTech A
Technician A says that radial tires should only be rotated front to rear, never side to
side. Tech b says that vehicle manufacturers usually recommend radial tires should
be rotated using the modified x method. Which is correct? - ANSWERTech b
For a tire that has excessive radial runout, tech a says that it should be broken down
on a tire changing machine and then rotated 180 degrees on the wheel and retested.
Tech b says that the tire should be replaced. Which tech is correct? - ANSWERTech
a
