1 | Page
RVTI Questions and Answers
where is the regulator in relation to the container?
Ans: Downstream
what does the first stage of the regulator reduce the pressure to?
Ans: approximately 10
lb/in2 gauge (PSIG)
what does the second stage of the regulator reduce the pressure
too?
Ans: 11 in WC
each magnet on a trailer brae system should draw how many
amps?
Ans: 3.2 amps max
what kind of lube should be used for slideouts?
Ans: dry lube
a class II hitch is rated for?
Ans: Class II hitches are weight carrying (WC) hitches rated up to 3500
lbs. gross trailer weight (GTW) with a maximum trailer tongue weight
(TW) of 300 lbs.
when performing a lockup test where should you put the
manometer?
Ans: barbed fitting on the test device
what position should the sweep seal be in?
© 2025 All rights reserved
, 2 | Page
Ans: na Inspect for proper contact with slide-out wall, roof, and floor;
verify good contact with each sealing surface; no rotting or cracks and
tears in rubber components
to operate the leveling system what position should the brakes be
in?
Ans: parking brake
should you use vise grips on propane tanks
Ans: no
where is the automatic change over regulator found?
Ans: inbetween two propane containers
on a new trailer the drums are seated after how many braking
applications?
Ans: after the first 200 miles of operation
What is the purpose of a propane regulator?
Ans: to reduce the pressure of the propane
What does it mean when you have a grid pattern on a laminated
sidewall?
Ans: Means it's a hung wall
Fiberglass is glued to the stud work
where should a motorhomes exhaust pipes be in relation to the
back of the motorhome?
Ans: Sticking out slightly past the back of the home
Why should you purge a new propane container
Ans: New propane containers could have air and water contaminants
creating false pressure
© 2025 All rights reserved
RVTI Questions and Answers
where is the regulator in relation to the container?
Ans: Downstream
what does the first stage of the regulator reduce the pressure to?
Ans: approximately 10
lb/in2 gauge (PSIG)
what does the second stage of the regulator reduce the pressure
too?
Ans: 11 in WC
each magnet on a trailer brae system should draw how many
amps?
Ans: 3.2 amps max
what kind of lube should be used for slideouts?
Ans: dry lube
a class II hitch is rated for?
Ans: Class II hitches are weight carrying (WC) hitches rated up to 3500
lbs. gross trailer weight (GTW) with a maximum trailer tongue weight
(TW) of 300 lbs.
when performing a lockup test where should you put the
manometer?
Ans: barbed fitting on the test device
what position should the sweep seal be in?
© 2025 All rights reserved
, 2 | Page
Ans: na Inspect for proper contact with slide-out wall, roof, and floor;
verify good contact with each sealing surface; no rotting or cracks and
tears in rubber components
to operate the leveling system what position should the brakes be
in?
Ans: parking brake
should you use vise grips on propane tanks
Ans: no
where is the automatic change over regulator found?
Ans: inbetween two propane containers
on a new trailer the drums are seated after how many braking
applications?
Ans: after the first 200 miles of operation
What is the purpose of a propane regulator?
Ans: to reduce the pressure of the propane
What does it mean when you have a grid pattern on a laminated
sidewall?
Ans: Means it's a hung wall
Fiberglass is glued to the stud work
where should a motorhomes exhaust pipes be in relation to the
back of the motorhome?
Ans: Sticking out slightly past the back of the home
Why should you purge a new propane container
Ans: New propane containers could have air and water contaminants
creating false pressure
© 2025 All rights reserved
