power engineeringpower
practice exam
engineering practice exam-2025
Study online at https://quizlet.com/_dhv1l5
1. Two canadadian codes which have been adopted by CSA B51 And B52
all canadian jurisdictions and which are of impor-
tance to fifth class power engineering are the:
2. The ASME code sections which are most pertinent to IV and VI
Fifth and Fourth class power engineer are sections:
3. what code contains guidelines for the care and op- ASME Section VI
eration of heating boilers?
4. When a feedwater pump feeds two of more boilers Each feedwater line to each
from a common source, there must be a regulating boiler
valve
5. what determines the classification of the certificate Kilowatt rating of the power-
of completency required for the role of chief power plant
engineer?
6. The provincial regulations require that all welding approved by an authorized
repairs on boilers must be: inspector
7. A boiler in which steam is made at a present not heating plant
greater than 103 Kilopascals, is properly termed a:
8. In the power engineers regulations definitions, Heating surface
______ means any part of the surface of a boiler that
is in contact with fluid under pressure on one side
and the products of combustion on the other side:
9. Heating plant means one or more boilers in which 1,100 kPa and a temp of 121c
water that can be heated pressure and temperature
of not more than:
10. The letters CRN stands for
www.stuvia.com
, power engineeringpower
practice exam
engineering practice exam-2025
Study online at https://quizlet.com/_dhv1l5
Canadian registration num-
ber
11. Heat passes through the metal of heating surfaces conduction
by:
12. Six kg would be a measure of an object's: mass
13. the term used to describe the fluid to gas change of evapotarion
state during the addition of heat is latent heat of:
14. the fahrenheit scale considers the boiling point of 212c
water to be
15. The three meathods of heat transfer are: Radiation, conduction and
convection
16. Water extinguishes a fire by: cooling the combustible ma-
terial
17. Water hammer can be prevented or minimized by "end of line" air
installing___ chambers on a piping system.
18. when working below ground level, the work pre- falling objects
sents the danger of :
19. Under WHMIS legislation all workers have the right Know what material they are
to working with
20. of the following materials, which would be classified Paper
as a class B fire?
21. The correct safe working angle for a ladder is: 1 to 4
22. falling objects
www.stuvia.com
practice exam
engineering practice exam-2025
Study online at https://quizlet.com/_dhv1l5
1. Two canadadian codes which have been adopted by CSA B51 And B52
all canadian jurisdictions and which are of impor-
tance to fifth class power engineering are the:
2. The ASME code sections which are most pertinent to IV and VI
Fifth and Fourth class power engineer are sections:
3. what code contains guidelines for the care and op- ASME Section VI
eration of heating boilers?
4. When a feedwater pump feeds two of more boilers Each feedwater line to each
from a common source, there must be a regulating boiler
valve
5. what determines the classification of the certificate Kilowatt rating of the power-
of completency required for the role of chief power plant
engineer?
6. The provincial regulations require that all welding approved by an authorized
repairs on boilers must be: inspector
7. A boiler in which steam is made at a present not heating plant
greater than 103 Kilopascals, is properly termed a:
8. In the power engineers regulations definitions, Heating surface
______ means any part of the surface of a boiler that
is in contact with fluid under pressure on one side
and the products of combustion on the other side:
9. Heating plant means one or more boilers in which 1,100 kPa and a temp of 121c
water that can be heated pressure and temperature
of not more than:
10. The letters CRN stands for
www.stuvia.com
, power engineeringpower
practice exam
engineering practice exam-2025
Study online at https://quizlet.com/_dhv1l5
Canadian registration num-
ber
11. Heat passes through the metal of heating surfaces conduction
by:
12. Six kg would be a measure of an object's: mass
13. the term used to describe the fluid to gas change of evapotarion
state during the addition of heat is latent heat of:
14. the fahrenheit scale considers the boiling point of 212c
water to be
15. The three meathods of heat transfer are: Radiation, conduction and
convection
16. Water extinguishes a fire by: cooling the combustible ma-
terial
17. Water hammer can be prevented or minimized by "end of line" air
installing___ chambers on a piping system.
18. when working below ground level, the work pre- falling objects
sents the danger of :
19. Under WHMIS legislation all workers have the right Know what material they are
to working with
20. of the following materials, which would be classified Paper
as a class B fire?
21. The correct safe working angle for a ladder is: 1 to 4
22. falling objects
www.stuvia.com
