Automatic Transmission Final Questions With Complete
Solutions
Technician A says when testing a switch , a test light is used at
the output of the switch in various switch positions . Technician
B says when checking a switch , a voltmeter is used at the output
of the switch in various switch positions . Who is correct ?
Both
Technician A says when checking voltage drops , the negative
meter lead is connected to ground and the positive lead is
connected to the component being tested Technician B says the
voltmeter is connected across the load with the circuit activated
when testing voltage drops . Who is correct ?
Tech B
Technician A says DTCs can be set by out of range signals from
electronic components . Technician B says remember to check
for hydraulic or mechanical problems causing DTCs . Who is
correct ?
Both
Technician A says the oil from your skin can cause corrosion of
electrical terminals . Technician B says do not remove a part
from its protective package until it is time to install the part .
Who is correct ?
Both
,Technician A says ohmmeters are used to test semiconductors .
Technician B says voltmeters are used to test semiconductors .
Who is correct ?
Tech A
Technician A ays some manufacturers monitor clutch volume
indexes . Technician B says this is part of an adaptive strategy .
Who is correct ?
Both
Technician A says the flywheel / alternator / starter assembly
may be positioned between the engine and the transmission and
it does not require the very high voltage of the IMA . Technician
B says the flywheel / alternator / starter assembly assists the
engine when additional power is needed . Who is correct ?
Tech B
Technician A says in the ISAD system , the stator of the unit is
mounted to the engine block . Technician B says the stator of the
ISAD system is mounted on the end of the crankshaft of the
engine . Who is correct ?
Tech A
Technician A says a slide hammer and the correct attachment
should be used to remove bushings . Technician B says that to
, easily remove bushings , they should be heated with a torch .
Who is correct ?
Tech A
Technician A says nearly all transmission problems can be
corrected by installing a rebuild kit . Technician B says a
technician should inspect the material in the filter before tearing
down the transmission or transaxle . Who is correct ?
Tech B
Technician A says when an external gear is in mesh with an
internal gear , the two gears will rotate in the same direction .
Technician B says there will be a torque increase when an
external gear drives and is in mesh with an internal gear . Who is
correct
Tech A
Tech A says a faulty output shaft can cause vibrations. Tech B
says an Unbalanced torque converter can cause vibrations. Who
is correct?
Both
Technician A says a faulty torque converter typically causes
abnormal noises from the transmission . Technician B says
faulty clutches or bands are never the cause of abnormal noise
from the transmission . Who is correct ?
Solutions
Technician A says when testing a switch , a test light is used at
the output of the switch in various switch positions . Technician
B says when checking a switch , a voltmeter is used at the output
of the switch in various switch positions . Who is correct ?
Both
Technician A says when checking voltage drops , the negative
meter lead is connected to ground and the positive lead is
connected to the component being tested Technician B says the
voltmeter is connected across the load with the circuit activated
when testing voltage drops . Who is correct ?
Tech B
Technician A says DTCs can be set by out of range signals from
electronic components . Technician B says remember to check
for hydraulic or mechanical problems causing DTCs . Who is
correct ?
Both
Technician A says the oil from your skin can cause corrosion of
electrical terminals . Technician B says do not remove a part
from its protective package until it is time to install the part .
Who is correct ?
Both
,Technician A says ohmmeters are used to test semiconductors .
Technician B says voltmeters are used to test semiconductors .
Who is correct ?
Tech A
Technician A ays some manufacturers monitor clutch volume
indexes . Technician B says this is part of an adaptive strategy .
Who is correct ?
Both
Technician A says the flywheel / alternator / starter assembly
may be positioned between the engine and the transmission and
it does not require the very high voltage of the IMA . Technician
B says the flywheel / alternator / starter assembly assists the
engine when additional power is needed . Who is correct ?
Tech B
Technician A says in the ISAD system , the stator of the unit is
mounted to the engine block . Technician B says the stator of the
ISAD system is mounted on the end of the crankshaft of the
engine . Who is correct ?
Tech A
Technician A says a slide hammer and the correct attachment
should be used to remove bushings . Technician B says that to
, easily remove bushings , they should be heated with a torch .
Who is correct ?
Tech A
Technician A says nearly all transmission problems can be
corrected by installing a rebuild kit . Technician B says a
technician should inspect the material in the filter before tearing
down the transmission or transaxle . Who is correct ?
Tech B
Technician A says when an external gear is in mesh with an
internal gear , the two gears will rotate in the same direction .
Technician B says there will be a torque increase when an
external gear drives and is in mesh with an internal gear . Who is
correct
Tech A
Tech A says a faulty output shaft can cause vibrations. Tech B
says an Unbalanced torque converter can cause vibrations. Who
is correct?
Both
Technician A says a faulty torque converter typically causes
abnormal noises from the transmission . Technician B says
faulty clutches or bands are never the cause of abnormal noise
from the transmission . Who is correct ?