RAMSAY MULTICRAFT SIMULATION TEST WITH VERIFIED ANSWERS
1. Staggered roller bearings are available in cylindrical, barrel
and taper shaped rollers.
2. Stroke What is the "x" in the following figure?
3. In-Direct Valve Which of the following uses a servo motor to actuate
the valve?
4. Check if there is a A solenoid valve is not opening. Which of the following
humming sound. CANNOT be the check of this failure?
5. Minimum The clearance volume is at the Top Dead
Center (TDC) of an engine.
6. Compression and Intake There are four cycles in IC Engines: Compressi
exhaust,
intake, and expansion. In two-stroke engines, two
functions are performed in one stroke. Which of the
following stages occurs simultaneously?
1/
101
,RAMSAY MULTICRAFT SIMULATION TEST WITH VERIFIED ANSWERS
7. Middle of TDC and BDC The instantaneous speed of the piston is maximum at
the
.
8. Thick A cylinder with a wall thickness of 6mm and whose
inner diameter is 100 mm is a walled
cylinder.
9. More economical and The advantage of intermittent welding is that it is:
Easier to repair in case of
failure.
10. 6.82 For a crane with a capacity of 25.6 tons, a self-weight
of 2.4 tons and a load of 3.75 tons, the safety factor
is:
2/
101
,RAMSAY MULTICRAFT SIMULATION TEST WITH VERIFIED ANSWERS
11. Axial
3/
101
, Ramsay MultiCraft Simulation
Test
load is acting on the plane of the bearings' axis
of rotation.
12. Zero-film are sliding Which of the following statements is true regarding
bearings which are lubri- cation?
lubrication-free.
13. ZN/p The characteristic number of the bearing is given
by: Z=absolute viscosity of the lubricant, N= speed
of journal, p=bearing pressure
14. Mist System Which of the following lubrication system is used in
two stroke engines?
15. Offset Bearing Also called eccentrically loaded bearing is:
16. 0.0010 For a journal bearing design, the clearance ratio
("clear- ance") should be approximately
considered as:
17. Used at the Low-Speed End Considering the power transmission through V-belt,
which
one is not
correct? V-belts
are:
18. 41.66 lbs How much is the ettort of the pulley system shown, if
the load is 250 lbs?
1. Staggered roller bearings are available in cylindrical, barrel
and taper shaped rollers.
2. Stroke What is the "x" in the following figure?
3. In-Direct Valve Which of the following uses a servo motor to actuate
the valve?
4. Check if there is a A solenoid valve is not opening. Which of the following
humming sound. CANNOT be the check of this failure?
5. Minimum The clearance volume is at the Top Dead
Center (TDC) of an engine.
6. Compression and Intake There are four cycles in IC Engines: Compressi
exhaust,
intake, and expansion. In two-stroke engines, two
functions are performed in one stroke. Which of the
following stages occurs simultaneously?
1/
101
,RAMSAY MULTICRAFT SIMULATION TEST WITH VERIFIED ANSWERS
7. Middle of TDC and BDC The instantaneous speed of the piston is maximum at
the
.
8. Thick A cylinder with a wall thickness of 6mm and whose
inner diameter is 100 mm is a walled
cylinder.
9. More economical and The advantage of intermittent welding is that it is:
Easier to repair in case of
failure.
10. 6.82 For a crane with a capacity of 25.6 tons, a self-weight
of 2.4 tons and a load of 3.75 tons, the safety factor
is:
2/
101
,RAMSAY MULTICRAFT SIMULATION TEST WITH VERIFIED ANSWERS
11. Axial
3/
101
, Ramsay MultiCraft Simulation
Test
load is acting on the plane of the bearings' axis
of rotation.
12. Zero-film are sliding Which of the following statements is true regarding
bearings which are lubri- cation?
lubrication-free.
13. ZN/p The characteristic number of the bearing is given
by: Z=absolute viscosity of the lubricant, N= speed
of journal, p=bearing pressure
14. Mist System Which of the following lubrication system is used in
two stroke engines?
15. Offset Bearing Also called eccentrically loaded bearing is:
16. 0.0010 For a journal bearing design, the clearance ratio
("clear- ance") should be approximately
considered as:
17. Used at the Low-Speed End Considering the power transmission through V-belt,
which
one is not
correct? V-belts
are:
18. 41.66 lbs How much is the ettort of the pulley system shown, if
the load is 250 lbs?
