FSNA Readiness – Questions With Logical Solutions
This type of device is a workstation used by an end user which provides the
user with access to the network. Correct Answer - Client
An ordinary Frame payload is how many Bytes in length? Correct Answer -
1500 Bytes
How many bits are there in 512 Bytes? Correct Answer - 4096
A MAC Address is comprised of how many total hexadecimal digits? Correct
Answer - 12
The last 6 hexadecimal digits (or the last 24 bits) in a MAC Address represent
the OUI (organizationally unique identifier) which identifies a vendor,
organization or manufacturer of the Network Interface Card to which the MAC
address is assigned. (True / false) Correct Answer - False
An IPv4 address is comprised of how many binary bits? Correct Answer -
32
Internet Protocol is included as part of which protocol stack? Correct
Answer - TCP/IP
A unicast is sent from a single sender to multiple receivers. (True / False)
Correct Answer - False
What does a MAC Broadcast Address look like in hexadecimal format?
Correct Answer - FF-FF-FF-FF-FF-FF
By default routers pass Broadcast traffic from one network to another
network. (True / False) Correct Answer - False
ARP is used to find the MAC address of a host when the IP address is known.
(True / False) Correct Answer - True
What is the IEEE standard for Ethernet? Correct Answer - 802.3
,What is the maximum distance of Ethernet over Twisted Pair cabling?
Correct Answer - 100 Meters
The size of a standard Ethernet frame is how many Bytes? Correct Answer -
1500 bites
Network devices that are on the same Ethernet segment are also in the same
_______________. Correct Answer - Collision Domain
Which part of Ethernet defines how devices know when to transmit on an
Ethernet segment. Correct Answer - CSMA/CD
Full Duplex communication is when a node can receive and transmit at the
same time. Correct Answer - True
An Ethernet Hub separates collision domains Correct Answer - False
What is the maximum data rate supported by Ethernet on Category 5e twisted
pair cable? Correct Answer - 1000Mbps
Which type of connector is used with standard twisted pair cables for
Ethernet networks? Correct Answer - RJ45
To create a straight-through twisted pair cable a different TIA/EIA standard
should be used on each side of the cable. Correct Answer - False
Which Ethernet naming syntax defines Gigabit Ethernet up to 100 Meters over
Cat5e or Cat 6 twisted pair cabling? Correct Answer - 1000Base-T
If a device or Ethernet connection is rated for 100BASE-TX what is the
maximum data rate (speed)? Correct Answer - 100Mbps
Which Ethernet naming syntax defines Gigabit Ethernet over multi-mode fiber
optic cable? Correct Answer - 1000BASE-SX
Which Ethernet naming syntax defines 10 Gigabit Ethernet over single-mode
up to 40 kilometers? Correct Answer - 10GBASE-ER
, In copper cabling the term STP refers to ___________________. Correct Answer -
Shielded Twisted Pair
Which of the following types of connectors is used in Plain Old Telephone
Service (POTS) connections? Correct Answer - RJ11
RG-6 and RG-59 are types of ____________ cable. Correct Answer - Coaxial
Multimode fiber optics has a longer distance rating than singlemode fiber
optics. Correct Answer - False
The __________ connector is a commonly used connector for coaxial cables for
connecting RG-6 cable to devices such as cable modems. Correct Answer -
F type
ST, SC, LC, and MT-RJ are all types of connectors for ____________ cables.
Correct Answer - Fiber Optic
The _____________ is a compact transceiver that plugs into a designated port on a
network device for connecting various types of fiber optic or twisted pair
connections. Replaces the older "GBIC" type of transceiver - referred to as a
"mini-GBIC". Correct Answer - SFP
Fiber optic cables are susceptible to electromagnetic interference (EMI). (True
/ False) Correct Answer - False
A _______________ is used to create network and phone system cables using
twisted pair cable and RJ type connectors. Correct Answer - Telco /
Network Crimper
This tool is used to confirm the wiremap of a cable and verify end to end
continuity across the cable. Correct Answer - Cable Tester
The Toner and Probe are used for locating specific cable runs Correct
Answer - True
This tool is used for testing the voltage on power outlets and power supplies
and well as testing copper wires for resistance and continuity. Correct
Answer - Multimeter
This type of device is a workstation used by an end user which provides the
user with access to the network. Correct Answer - Client
An ordinary Frame payload is how many Bytes in length? Correct Answer -
1500 Bytes
How many bits are there in 512 Bytes? Correct Answer - 4096
A MAC Address is comprised of how many total hexadecimal digits? Correct
Answer - 12
The last 6 hexadecimal digits (or the last 24 bits) in a MAC Address represent
the OUI (organizationally unique identifier) which identifies a vendor,
organization or manufacturer of the Network Interface Card to which the MAC
address is assigned. (True / false) Correct Answer - False
An IPv4 address is comprised of how many binary bits? Correct Answer -
32
Internet Protocol is included as part of which protocol stack? Correct
Answer - TCP/IP
A unicast is sent from a single sender to multiple receivers. (True / False)
Correct Answer - False
What does a MAC Broadcast Address look like in hexadecimal format?
Correct Answer - FF-FF-FF-FF-FF-FF
By default routers pass Broadcast traffic from one network to another
network. (True / False) Correct Answer - False
ARP is used to find the MAC address of a host when the IP address is known.
(True / False) Correct Answer - True
What is the IEEE standard for Ethernet? Correct Answer - 802.3
,What is the maximum distance of Ethernet over Twisted Pair cabling?
Correct Answer - 100 Meters
The size of a standard Ethernet frame is how many Bytes? Correct Answer -
1500 bites
Network devices that are on the same Ethernet segment are also in the same
_______________. Correct Answer - Collision Domain
Which part of Ethernet defines how devices know when to transmit on an
Ethernet segment. Correct Answer - CSMA/CD
Full Duplex communication is when a node can receive and transmit at the
same time. Correct Answer - True
An Ethernet Hub separates collision domains Correct Answer - False
What is the maximum data rate supported by Ethernet on Category 5e twisted
pair cable? Correct Answer - 1000Mbps
Which type of connector is used with standard twisted pair cables for
Ethernet networks? Correct Answer - RJ45
To create a straight-through twisted pair cable a different TIA/EIA standard
should be used on each side of the cable. Correct Answer - False
Which Ethernet naming syntax defines Gigabit Ethernet up to 100 Meters over
Cat5e or Cat 6 twisted pair cabling? Correct Answer - 1000Base-T
If a device or Ethernet connection is rated for 100BASE-TX what is the
maximum data rate (speed)? Correct Answer - 100Mbps
Which Ethernet naming syntax defines Gigabit Ethernet over multi-mode fiber
optic cable? Correct Answer - 1000BASE-SX
Which Ethernet naming syntax defines 10 Gigabit Ethernet over single-mode
up to 40 kilometers? Correct Answer - 10GBASE-ER
, In copper cabling the term STP refers to ___________________. Correct Answer -
Shielded Twisted Pair
Which of the following types of connectors is used in Plain Old Telephone
Service (POTS) connections? Correct Answer - RJ11
RG-6 and RG-59 are types of ____________ cable. Correct Answer - Coaxial
Multimode fiber optics has a longer distance rating than singlemode fiber
optics. Correct Answer - False
The __________ connector is a commonly used connector for coaxial cables for
connecting RG-6 cable to devices such as cable modems. Correct Answer -
F type
ST, SC, LC, and MT-RJ are all types of connectors for ____________ cables.
Correct Answer - Fiber Optic
The _____________ is a compact transceiver that plugs into a designated port on a
network device for connecting various types of fiber optic or twisted pair
connections. Replaces the older "GBIC" type of transceiver - referred to as a
"mini-GBIC". Correct Answer - SFP
Fiber optic cables are susceptible to electromagnetic interference (EMI). (True
/ False) Correct Answer - False
A _______________ is used to create network and phone system cables using
twisted pair cable and RJ type connectors. Correct Answer - Telco /
Network Crimper
This tool is used to confirm the wiremap of a cable and verify end to end
continuity across the cable. Correct Answer - Cable Tester
The Toner and Probe are used for locating specific cable runs Correct
Answer - True
This tool is used for testing the voltage on power outlets and power supplies
and well as testing copper wires for resistance and continuity. Correct
Answer - Multimeter
