• ¿Documento equivocado? Cámbialo gratis
  • Escrito por estudiantes que aprobaron
  • Inmediatamente disponible después del pago
  • Leer en línea o como PDF
Vender
¿Dónde estudias?
Tu idioma
Document preview thumbnail
Vista previa 2 fuera de 6 páginas
Otro

Module 9: Ymca Submax Test Protocol| Latest 2025 Updated Solution

Document preview thumbnail
Vista previa 2 fuera de 6 páginas

MODULE 9: YMCA SUBMAX TEST PROTOCOL| LATEST 2025 UPDATED SOLUTION Objective of the test The objective of the YMCA submaximal cycle test is to obtain and plot two steady-state* heart rate values between 110 bpm and the 85% of age predicted maximum heart rate. To attain this objective, a person may need to cycle for up to four stages. *average of the last two minutes during each stage Measurements during the test During the test, we assess and record the following on a data sheet: • o Heart rate: every minute (during the last 15s of the minute) o Blood pressure: once every stage in the third minute of the stage o RPE: once every stage in the third minute of the stage. Each Stage lasts at least 3 minutes with the resistance changing after the first stage based on the whether the participant has achieved "Steady-state" Steady-State Definition How do you know if the heart rate is at steady state? Steady state is determined by two heart rates being ≤ 5 beats per minute apart. Note that we measure heart rate every minute during the YMCA submax test. At a minimum, a stage must be 3min long. So, if heart rate in the 2nd and 3rd minutes is within 5 bpm, that would imply steady state. However, if the difference is 5bpm, you would need to extend the stage by 1 more minute (at least). To establish the line of best fit on the graph, at least two HR data points are needed, ideally between 110bpm and 85% of age predicted maximum heart rate. • o If difference between minute 2 and minute 3 HR = 5 bpm in Stage 1, use the appropriate Stage 2 resistance based on the chart below and continue to use the same column for each subsequent stage. o If difference between minute 2 and minute 3 HR 5 bpm, continue at the same stage for 1 more minute. Only move to next stage after steady state HR is established [i.e. = 5bpm difference between HR for last 2 minutes of a stage]. Average the last two heart rates in each stage before you plot the data. Example flowchart of how to run a test

Vista previa del contenido

MODULE 9: YMCA SUBMAX TEST PROTOCOL| LATEST 2025
UPDATED SOLUTION

Objective of the test
The objective of the YMCA submaximal cycle test is to obtain and plot two steady-
state* heart rate values between 110 bpm and the 85% of age predicted maximum
heart rate. To attain this objective, a person may need to cycle for up to four stages.
*average of the last two minutes during each stage

Measurements during the test
During the test, we assess and record the following on a data sheet:
•
o Heart rate: every minute (during the last 15s of the minute)
o Blood pressure: once every stage in the third minute of the stage
o RPE: once every stage in the third minute of the stage.




Each Stage lasts at least 3 minutes with the resistance changing after the first stage
based on the whether the participant has achieved "Steady-state"

Steady-State Definition
How do you know if the heart rate is at steady state? Steady state is determined by
two heart rates being ≤ 5 beats per minute apart. Note that we measure heart rate
every minute during the YMCA submax test. At a minimum, a stage must be 3min
long. So, if heart rate in the 2nd and 3rd minutes is within 5 bpm, that would imply
steady state. However, if the difference is > 5bpm, you would need to extend the stage
by 1 more minute (at least). To establish the line of best fit on the graph, at least two HR
data points are needed, ideally between 110bpm and 85% of age predicted maximum
heart rate.
•


https://www.stuvia.com/user/Mboffin

, o If difference between minute 2 and minute 3 HR <= 5 bpm in Stage
1, use the appropriate Stage 2 resistance based on the chart below
and continue to use the same column for each subsequent stage.
o If difference between minute 2 and minute 3 HR > 5 bpm, continue
at the same stage for 1 more minute. Only move to next stage after
steady state HR is established [i.e. <= 5bpm difference between
HR for last 2 minutes of a stage]. Average the last two heart
rates in each stage before you plot the data.




Example flowchart of how to run a test




https://www.stuvia.com/user/Mboffin

Información del documento

Subido en
30 de julio de 2025
Número de páginas
6
Escrito en
2024/2025
Tipo
Otro
Personaje
Desconocido
$17.49

¿Documento equivocado? Cámbialo gratis Dentro de los 14 días posteriores a la compra y antes de descargarlo, puedes elegir otro documento. Puedes gastar el importe de nuevo.
Escrito por estudiantes que aprobaron
Inmediatamente disponible después del pago
Leer en línea o como PDF

Seller avatar
Los indicadores de reputación están sujetos a la cantidad de artículos vendidos por una tarifa y las reseñas que ha recibido por esos documentos. Hay tres niveles: Bronce, Plata y Oro. Cuanto mayor reputación, más podrás confiar en la calidad del trabajo del vendedor.
MBOFFIN
3.7
(140)
Vendido
788
Seguidores
218
Artículos
5732
Última venta
19 horas hace



Por qué los estudiantes eligen Stuvia

Creado por compañeros estudiantes, verificado por reseñas

Calidad en la que puedes confiar: escrito por estudiantes que aprobaron y evaluado por otros que han usado estos resúmenes.

¿No estás satisfecho? Elige otro documento

¡No te preocupes! Puedes elegir directamente otro documento que se ajuste mejor a lo que buscas.

Paga como quieras, empieza a estudiar al instante

Sin suscripción, sin compromisos. Paga como estés acostumbrado con tarjeta de crédito y descarga tu documento PDF inmediatamente.

Student with book image

“Comprado, descargado y aprobado. Así de fácil puede ser.”

Alisha Student

Preguntas frecuentes