AE 416 ACTUAL EXAM 1 NEWEST VERSION 2025-2026 \LATEST
VERSION WITH COMPLETE QUESTIONS AND CORRECT
DETAILED ANSWERS \ASSURED PASS ALREADY GRADED A+
deformation band a deformation causes the crush to start in the middle
do honeycombs absorb more out of plane
energy when crushed in-
plane or out-of-plane?
where does the the middle
deformation start on a
honeycomb crushed in-
plane?
how does a honeycomb top to bottom
deform when crushed out-
of-plane?
The initial peak stress pre-crushing
(compressive
strength) is normally much
higher than the plateau
stress (crush strength). What
eases this issue?
select a packaging material whose plateau stress is low
what is an ideal packaging
material? enough to not damage the object, yet thick enough to
absorb all kinetic energy
-Grids: draw/etch a grid onto the surface of an object
Measuring strain through
and observe how the grid changes upon straining
grids and coatings
-Coatings: brittle coatings designed to crack are also effective
-bonds an electrical conductor to a specimen (insulated between
Electrical Resistance Strain them)
Gage -measures changes of electrical resistance as it's strained
- epsilon = [(delta R)/R]/GF
/ 1/19
,7/5/25, 8:01 PM AE 416 EXAM 1
R = pL/A
electrical resistance of a p = resistivity
conductor
-ohmmeter, Wheatstone bridge
large resistance change for relatively small strains
what do high gage factors
lead to? -advantageous because it requires less sensitive circuitry
- wire/foil is from materials like constantan whose
resistance is relatively constant over a wide
What are foil strain gages
made of? temperature range
-backing is made from an insulator such as polyamide (plastic)
-sodering tabs included
-clean specimen w/M-Prep cleaning materials
-position gage over test point with tape
-apply catalyst to gage
strain gage installation steps -apply adhesive to application area
-install gage with uniform thumb pressure over tape
-remove tape from bonded gage
-solder wires to the leads and connect to measuring device
R vs R ' ? R ' (R prime) indicates "new resistance" after straining
-better accuracy by measuring a small, but very strain
sensitive voltage Vm between 2 points
-for low level signals, a high gain amplifier can boost the
Wheatstone bridge signal to noise ratio without saturation
-the circuit is easily zero adjusted (potentiometer) to
compensate for dissimilar resistors/strain gages ...
"balancing the bridge"
How many strain gages 1
in a quarter bridge?
how many strain gages in a 2
half bridge?
how many strain gages in a 4
full bridge?
What happens when 2 the signal strength doubles
identical strain
gages are connected in
opposite positions in the
bridge and are strained the
/ 2/19
, 7/5/25, 8:01 PM AE 416 EXAM 1
same?
What happens with a full can further increase the output if appropriately mounted
bridge of strain gages? (opposite sides of a cantilever beam)
What does inappropriate leads to zero output
mounting of strain gages
do?
elastic deflection theta = LT/KG
torsion failure Tf = K(sigma)/d
a torque applied to a bar/shaft an angle of twist (theta)
produces
________
angle of twist for an isotropic theta = TL/GJ
bar
Tresca predicts yielding when Tau_max > sigma_y/2
for a solid ellipsoid, square, points closest to the centroid of that section (find the
rectangular, and triangular largest circle that can fit into the section of interest,
sections (non-circular), then treat the shape as a circular section of that
where is the maximum surface diameter)
stress?
if one or more dimensions is very small relative to the
When does buckling occur?
others (torqued thin wall tubes, compressed thin
columns, and other shapes)
-zero (tare) with no sample
-rotate to zero degrees
how to use the lo-torque -insert and clamp sample
torsion testing machine -slightly rotate to relieve induced load
apply torque to samples? -slowly load sample
-read torque directly
what is used for checking dead weights
accuracy of mass scales and
force loadcells?
why is torsion more the moment arm
complex to check for
accuracy?
what is used to check the torque wrench
accuracy of torsion?
What does the Model P3 measures strain
/ 3/19