AMT 102 PREPWARE GENERAL - AIRCRAFT
DRAWINGS
8103. What type of line is normally used in a mechanical drawing or blueprint to
represent an edge or object not visible the the viewer? - Answers - A-Medium-weight
dashed line.
8104. (Refer to Figure 27.) In the isometric view of a typical aileron balance weight,
identify the view indicated by the arrow. - Answers - B-3.
8105.
(1) A detail drawing is a description of a single part.
(2) An assembly drawing is a description of an object made up of two or more parts.
Regarding the above statements, - Answers - C-both No. 1 and No. 2 are true.
8106. (Refer to Figure 28.) Identify the bottom view of the object shown. - Answers - A-
2.
8107. A specific measured distance from the datum or some other point identified by the
manufacturer, to a point in or on the aircraft is called a - Answers - A-station number.
8108. Which statement is true regarding an orthographic projection? - Answers - C-
One-view, two-view, and three-view drawings are the most common.
8109. (Refer to Figure 29.) Identify the left side view of the object shown. - Answers -
C-3.
8110. A line used to show an edge which is not visible is a - Answers - B-hidden line.
8110-1. What type of drawing line consists of alternating long and short lines? -
Answers - B-Center.
8111. (Refer to Figure 30.) Identify the bottom view of the object. - Answers - A-1.
8112.
(1) Schematic diagrams indicate the location of individual components in the aircraft.
(2) Schematic diagrams indicate the location of components with respect to each other
within the system.
Regarding the above statements, - Answers - C-only No. 2 is true.
8113. (Refer to Figure 31.) What are the proper procedural steps for sketching repairs
and alterations? - Answers - A-3, 1, 4, 2.
, 8114. Which statement is applicable when using a sketch for making a part? - Answers
- B-The sketch must show all information to manufacture the part.
8115. (Refer to Figure 32.) Wha is the next step required for a working sketch of the
illustration? - Answers - B-Sketch extension and dimension lines.
8116. For sketching purposes, almost all objects are composed of one or some
combination of six basic shapes; these include the - Answers - A-angle, arc, line,
plane, square, and circle.
8116-1. In a sectional view drawing, that sections illustrate particular parts of an object?
- Answers - A-Removed.
8117. What should be the first step of the procedure in sketching an aircraft wing skin
repair? - Answers - C-Block in the views.
8117-1. A simple way to find the center of a circle on a sketch or drawing, or a circular
piece of material is to - Answers - A-draw two non-parallel chord lines across the circle
and then a corresponding perpendicular bisector line across each chord line.
8118.
(1) According to 14 CFR Part 91, repairs to an aircraft skin should have a detailed
dimensional sketch included in the permanent records.
(2) On occasion, a mechanic may need to make a simple sketch of a proposed repair to
an aircraft, a new design, or a modification.
Regarding the above statements, - Answers - B-only No. 2 is true.
8119. Working drawings may be divided into three classes. They are: - Answers - B-
detail drawings, assembly drawings, and installation drawings.
8119-1. What is the class of working drawing that is the description/depiction of a single
part? - Answers - C-Detail drawing.
8120. Sketches are usually made easier by the use of - Answers - A-graph paper.
8120-1.
(1) Sketches are usually made with the aid of drafting instruments.
(2) Sketches are usually more complicated to make when using graph paper.
Regarding the above statements, - Answers - C-Neither No. 1 nor No. 2 is true.
8121. What material symbol is frequently used in drawings to represent all metals? -
Answers - B-Cast iron.
DRAWINGS
8103. What type of line is normally used in a mechanical drawing or blueprint to
represent an edge or object not visible the the viewer? - Answers - A-Medium-weight
dashed line.
8104. (Refer to Figure 27.) In the isometric view of a typical aileron balance weight,
identify the view indicated by the arrow. - Answers - B-3.
8105.
(1) A detail drawing is a description of a single part.
(2) An assembly drawing is a description of an object made up of two or more parts.
Regarding the above statements, - Answers - C-both No. 1 and No. 2 are true.
8106. (Refer to Figure 28.) Identify the bottom view of the object shown. - Answers - A-
2.
8107. A specific measured distance from the datum or some other point identified by the
manufacturer, to a point in or on the aircraft is called a - Answers - A-station number.
8108. Which statement is true regarding an orthographic projection? - Answers - C-
One-view, two-view, and three-view drawings are the most common.
8109. (Refer to Figure 29.) Identify the left side view of the object shown. - Answers -
C-3.
8110. A line used to show an edge which is not visible is a - Answers - B-hidden line.
8110-1. What type of drawing line consists of alternating long and short lines? -
Answers - B-Center.
8111. (Refer to Figure 30.) Identify the bottom view of the object. - Answers - A-1.
8112.
(1) Schematic diagrams indicate the location of individual components in the aircraft.
(2) Schematic diagrams indicate the location of components with respect to each other
within the system.
Regarding the above statements, - Answers - C-only No. 2 is true.
8113. (Refer to Figure 31.) What are the proper procedural steps for sketching repairs
and alterations? - Answers - A-3, 1, 4, 2.
, 8114. Which statement is applicable when using a sketch for making a part? - Answers
- B-The sketch must show all information to manufacture the part.
8115. (Refer to Figure 32.) Wha is the next step required for a working sketch of the
illustration? - Answers - B-Sketch extension and dimension lines.
8116. For sketching purposes, almost all objects are composed of one or some
combination of six basic shapes; these include the - Answers - A-angle, arc, line,
plane, square, and circle.
8116-1. In a sectional view drawing, that sections illustrate particular parts of an object?
- Answers - A-Removed.
8117. What should be the first step of the procedure in sketching an aircraft wing skin
repair? - Answers - C-Block in the views.
8117-1. A simple way to find the center of a circle on a sketch or drawing, or a circular
piece of material is to - Answers - A-draw two non-parallel chord lines across the circle
and then a corresponding perpendicular bisector line across each chord line.
8118.
(1) According to 14 CFR Part 91, repairs to an aircraft skin should have a detailed
dimensional sketch included in the permanent records.
(2) On occasion, a mechanic may need to make a simple sketch of a proposed repair to
an aircraft, a new design, or a modification.
Regarding the above statements, - Answers - B-only No. 2 is true.
8119. Working drawings may be divided into three classes. They are: - Answers - B-
detail drawings, assembly drawings, and installation drawings.
8119-1. What is the class of working drawing that is the description/depiction of a single
part? - Answers - C-Detail drawing.
8120. Sketches are usually made easier by the use of - Answers - A-graph paper.
8120-1.
(1) Sketches are usually made with the aid of drafting instruments.
(2) Sketches are usually more complicated to make when using graph paper.
Regarding the above statements, - Answers - C-Neither No. 1 nor No. 2 is true.
8121. What material symbol is frequently used in drawings to represent all metals? -
Answers - B-Cast iron.
