Hvac Journeyman Exam \| \| \|
QUESTIONS WITH ANSWERS \| \|
Defects on gas piping or fittings shall be _____.(A) repaired(B)
\| \| \| \| \| \| \| \| \| \|
replaced or repaired and retested(C) repaired by a certified
\| \| \| \| \| \| \| \| \|
welder(D) ignored, as the operating pressure is much less than
\| \| \| \| \| \| \| \| \| \|
the air test. - CORRECT ANSWERS ✔✔B. Fitting shall be replaced
\| \| \| \| \| \| \| \| \| \| \|
or repaired and retested. UMC Section 1316.4.3
\| \| \| \| \| \|
Every absorption refrigerating system supported from the ground
\| \| \| \| \| \| \| \|
shall rest on a concrete slab extending not less than _____ the
\| \| \| \| \| \| \| \| \| \| \| \|
adjoining ground level.(A) 3 inches below(B) 3 inches above (C) 6
\| \| \| \| \| \| \| \| \| \| \|
inches below(D) 6 inches above. - CORRECT ANSWERS ✔✔B. Slab
\| \| \| \| \| \| \| \| \| \|
extending not less than 3" above the adjoining ground level. UMC
\| \| \| \| \| \| \| \| \| \| \|
Section 1106.2 \|
Any part of a venting system installed at an angle greater than 45
\| \| \| \| \| \| \| \| \| \| \| \| \|
degrees from the vertical is considered by code to be _____.(A)
\| \| \| \| \| \| \| \| \| \| \|
vertica(B) horizontal l (C) a flat vent (D) an offset vent - CORRECT
\| \| \| \| \| \| \| \| \| \| \| \| \|
ANSWERS ✔✔B. any part of the venting installed at an angle \| \| \| \| \| \| \| \| \| \| \|
GREATER than 45 degrees is considered by this code to be
\| \| \| \| \| \| \| \| \| \| \|
Horizontal UMC Section 802.6.1.1 \| \| \|
Listed transition ducts f or clothes dryers shall not exceed_____
\| \| \| \| \| \| \| \| \| \|
feet in length. A.3 B.4 C.5 D.6. - CORRECT ANSWERS ✔✔D. Dryers
\| \| \| \| \| \| \| \| \| \| \| \|
shall not exceed 6 feet in length. UMC Section 504.3.2.1
\| \| \| \| \| \| \| \| \|
,Industrial product-conveying ducts and their fittings for abrasive
\| \| \| \| \| \| \| \|
and nonabrasive dust or solid materials shall be constructed of
\| \| \| \| \| \| \| \| \| \|
_____.(A) sheet meta(B) polyvinyl chloride l (C) fiberglass (D) A
\| \| \| \| \| \| \| \| \| \|
and C apply - CORRECT ANSWERS ✔✔A. Shall Be Constructed of
\| \| \| \| \| \| \| \| \| \| \|
sheet metal. UMC Section. 5 0 6.1
\| \| \| \| \| \|
Industrial product-conveying ducts and their fittings for abrasive
\| \| \| \| \| \| \| \|
and nonabrasive dust or solid materials shall be constructed of
\| \| \| \| \| \| \| \| \| \|
_____.(A) sheet metal ((B) polyvinyl chloride C) fiberglass (D) A
\| \| \| \| \| \| \| \| \| \|
and C apply - CORRECT ANSWERS ✔✔A 511.2
\| \| \| \| \| \| \|
Unlisted vented gas fireplaces shall have a clearance at the sides
\| \| \| \| \| \| \| \| \| \| \|
and rear of not less than _____ inches. Is the Answer: A. 10" B. 12"
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \|
C 16" D. 18". - CORRECT ANSWERS ✔✔D. clearance of an unlisted
\| \| \| \| \| \| \| \| \| \| \| \|
vented gas fireplace at the sides and the rear not less than 18".
\| \| \| \| \| \| \| \| \| \| \| \| \|
UMC Section 908.2(B) \| \|
Leaks in gas piping shall be located _____.(A) with a sniffer(B) with
\| \| \| \| \| \| \| \| \| \| \| \|
a presto-lite flame (C) with a noncorrosive leak-detecting fluid (D)
\| \| \| \| \| \| \| \| \| \|
by increasing the air pressure during a test until the leaks are
\| \| \| \| \| \| \| \| \| \| \| \|
heard as a whistle. - CORRECT ANSWERS ✔✔C. leaks in a gas
\| \| \| \| \| \| \| \| \| \| \| \|
piping shall be located with a non corrosive leak detecting fluid.
\| \| \| \| \| \| \| \| \| \| \|
UMC Section 1316.4.2 \| \|
Condensate drain piping shall have a slope of not less than _____ \| \| \| \| \| \| \| \| \| \| \| \|
inch per foot. A 1⁄8" B.¼" C.½" D. 1" - CORRECT ANSWERS ✔✔A.
\| \| \| \| \| \| \| \| \| \| \| \| \|
Slope of not less than 1/8" per foot. UMC Section 309.1
\| \| \| \| \| \| \| \| \| \|
The minimum gauge or size steel wire used to support horizontal
\| \| \| \| \| \| \| \| \| \| \|
metal ducts 10 inches or less in size is _____. A.14 AWG B.16 AWG
\| \| \| \| \| \| \| \| \| \| \| \| \| \|
, C.18 AWG D.20 AWG - CORRECT ANSWERS ✔✔C. 18 Minimum
\| \| \| \| \| \| \| \| \| \|
Gauge note: AWG is the abbreviation for "gauge size" Table 6-7(B)
\| \| \| \| \| \| \| \| \| \|
When smoke detectors are required as part of an automatic
\| \| \| \| \| \| \| \| \| \|
shutoff system, they shall be installed in the _____. A. return air
\| \| \| \| \| \| \| \| \| \| \| \|
duct ahead of any fresh-air inlet(B) main supply air duct served by
\| \| \| \| \| \| \| \| \| \| \| \|
such equipment(C) fresh-air inlet(D) main return and the main
\| \| \| \| \| \| \| \| \|
supply duct. - CORRECT ANSWERS ✔✔B. shall be installed in the
\| \| \| \| \| \| \| \| \| \| \|
main supply air duct served by equipment. UMC Section 609.0(5)
\| \| \| \| \| \| \| \| \|
The largest fuel-burning appliance allowed in a room 100'W x 20'L
\| \| \| \| \| \| \| \| \| \| \|
x 8'H without combustion air openingsis _____ Btu.(A) 80,000 (C)
\| \| \| \| \| \| \| \| \| \|
140,000(B) 100,000 (D) 320,000 - CORRECT ANSWERS ✔✔31 D. \| \| \| \| \| \| \| \| \|
701.2.1
Return air ducts that serve a dwelling unit shall be permitted to be
\| \| \| \| \| \| \| \| \| \| \| \| \|
of _____ construction? A.non-combustible B. combustible C. rated
\| \| \| \| \| \| \| \|
D. none of the above. - CORRECT ANSWERS ✔✔B. Shall be
\| \| \| \| \| \| \| \| \| \| \|
permitted to be of combustible type UMC Section 602.2 Ex (1)\| \| \| \| \| \| \| \| \| \|
Solid fuel-burning appliances _____ be connected to a venting
\| \| \| \| \| \| \| \| \|
system that serves a gas- or oil-burningappliance.(A) shall (B)
\| \| \| \| \| \| \| \| \|
may (C) shall not(D) with special approval may - CORRECT
\| \| \| \| \| \| \| \| \| \|
ANSWERS ✔✔C. appliances shall not UMC Section 802.5.5.1 \| \| \| \| \| \| \|
Any joint obtained by joining of metal parts with alloys that melt
\| \| \| \| \| \| \| \| \| \| \| \|
at temperatures higher than 840°F, but lowerthan the melting
\| \| \| \| \| \| \| \| \|
temperature of the parts to be joined, is a _____ joint.(A) brazed(B) \| \| \| \| \| \| \| \| \| \| \| \|
fused (D) soldered (C) welded - CORRECT ANSWERS ✔✔A. Is a
\| \| \| \| \| \| \| \| \| \| \|
brazed joint UMC section 2 1 2.0 \| \| \| \| \| \|
QUESTIONS WITH ANSWERS \| \|
Defects on gas piping or fittings shall be _____.(A) repaired(B)
\| \| \| \| \| \| \| \| \| \|
replaced or repaired and retested(C) repaired by a certified
\| \| \| \| \| \| \| \| \|
welder(D) ignored, as the operating pressure is much less than
\| \| \| \| \| \| \| \| \| \|
the air test. - CORRECT ANSWERS ✔✔B. Fitting shall be replaced
\| \| \| \| \| \| \| \| \| \| \|
or repaired and retested. UMC Section 1316.4.3
\| \| \| \| \| \|
Every absorption refrigerating system supported from the ground
\| \| \| \| \| \| \| \|
shall rest on a concrete slab extending not less than _____ the
\| \| \| \| \| \| \| \| \| \| \| \|
adjoining ground level.(A) 3 inches below(B) 3 inches above (C) 6
\| \| \| \| \| \| \| \| \| \| \|
inches below(D) 6 inches above. - CORRECT ANSWERS ✔✔B. Slab
\| \| \| \| \| \| \| \| \| \|
extending not less than 3" above the adjoining ground level. UMC
\| \| \| \| \| \| \| \| \| \| \|
Section 1106.2 \|
Any part of a venting system installed at an angle greater than 45
\| \| \| \| \| \| \| \| \| \| \| \| \|
degrees from the vertical is considered by code to be _____.(A)
\| \| \| \| \| \| \| \| \| \| \|
vertica(B) horizontal l (C) a flat vent (D) an offset vent - CORRECT
\| \| \| \| \| \| \| \| \| \| \| \| \|
ANSWERS ✔✔B. any part of the venting installed at an angle \| \| \| \| \| \| \| \| \| \| \|
GREATER than 45 degrees is considered by this code to be
\| \| \| \| \| \| \| \| \| \| \|
Horizontal UMC Section 802.6.1.1 \| \| \|
Listed transition ducts f or clothes dryers shall not exceed_____
\| \| \| \| \| \| \| \| \| \|
feet in length. A.3 B.4 C.5 D.6. - CORRECT ANSWERS ✔✔D. Dryers
\| \| \| \| \| \| \| \| \| \| \| \|
shall not exceed 6 feet in length. UMC Section 504.3.2.1
\| \| \| \| \| \| \| \| \|
,Industrial product-conveying ducts and their fittings for abrasive
\| \| \| \| \| \| \| \|
and nonabrasive dust or solid materials shall be constructed of
\| \| \| \| \| \| \| \| \| \|
_____.(A) sheet meta(B) polyvinyl chloride l (C) fiberglass (D) A
\| \| \| \| \| \| \| \| \| \|
and C apply - CORRECT ANSWERS ✔✔A. Shall Be Constructed of
\| \| \| \| \| \| \| \| \| \| \|
sheet metal. UMC Section. 5 0 6.1
\| \| \| \| \| \|
Industrial product-conveying ducts and their fittings for abrasive
\| \| \| \| \| \| \| \|
and nonabrasive dust or solid materials shall be constructed of
\| \| \| \| \| \| \| \| \| \|
_____.(A) sheet metal ((B) polyvinyl chloride C) fiberglass (D) A
\| \| \| \| \| \| \| \| \| \|
and C apply - CORRECT ANSWERS ✔✔A 511.2
\| \| \| \| \| \| \|
Unlisted vented gas fireplaces shall have a clearance at the sides
\| \| \| \| \| \| \| \| \| \| \|
and rear of not less than _____ inches. Is the Answer: A. 10" B. 12"
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \|
C 16" D. 18". - CORRECT ANSWERS ✔✔D. clearance of an unlisted
\| \| \| \| \| \| \| \| \| \| \| \|
vented gas fireplace at the sides and the rear not less than 18".
\| \| \| \| \| \| \| \| \| \| \| \| \|
UMC Section 908.2(B) \| \|
Leaks in gas piping shall be located _____.(A) with a sniffer(B) with
\| \| \| \| \| \| \| \| \| \| \| \|
a presto-lite flame (C) with a noncorrosive leak-detecting fluid (D)
\| \| \| \| \| \| \| \| \| \|
by increasing the air pressure during a test until the leaks are
\| \| \| \| \| \| \| \| \| \| \| \|
heard as a whistle. - CORRECT ANSWERS ✔✔C. leaks in a gas
\| \| \| \| \| \| \| \| \| \| \| \|
piping shall be located with a non corrosive leak detecting fluid.
\| \| \| \| \| \| \| \| \| \| \|
UMC Section 1316.4.2 \| \|
Condensate drain piping shall have a slope of not less than _____ \| \| \| \| \| \| \| \| \| \| \| \|
inch per foot. A 1⁄8" B.¼" C.½" D. 1" - CORRECT ANSWERS ✔✔A.
\| \| \| \| \| \| \| \| \| \| \| \| \|
Slope of not less than 1/8" per foot. UMC Section 309.1
\| \| \| \| \| \| \| \| \| \|
The minimum gauge or size steel wire used to support horizontal
\| \| \| \| \| \| \| \| \| \| \|
metal ducts 10 inches or less in size is _____. A.14 AWG B.16 AWG
\| \| \| \| \| \| \| \| \| \| \| \| \| \|
, C.18 AWG D.20 AWG - CORRECT ANSWERS ✔✔C. 18 Minimum
\| \| \| \| \| \| \| \| \| \|
Gauge note: AWG is the abbreviation for "gauge size" Table 6-7(B)
\| \| \| \| \| \| \| \| \| \|
When smoke detectors are required as part of an automatic
\| \| \| \| \| \| \| \| \| \|
shutoff system, they shall be installed in the _____. A. return air
\| \| \| \| \| \| \| \| \| \| \| \|
duct ahead of any fresh-air inlet(B) main supply air duct served by
\| \| \| \| \| \| \| \| \| \| \| \|
such equipment(C) fresh-air inlet(D) main return and the main
\| \| \| \| \| \| \| \| \|
supply duct. - CORRECT ANSWERS ✔✔B. shall be installed in the
\| \| \| \| \| \| \| \| \| \| \|
main supply air duct served by equipment. UMC Section 609.0(5)
\| \| \| \| \| \| \| \| \|
The largest fuel-burning appliance allowed in a room 100'W x 20'L
\| \| \| \| \| \| \| \| \| \| \|
x 8'H without combustion air openingsis _____ Btu.(A) 80,000 (C)
\| \| \| \| \| \| \| \| \| \|
140,000(B) 100,000 (D) 320,000 - CORRECT ANSWERS ✔✔31 D. \| \| \| \| \| \| \| \| \|
701.2.1
Return air ducts that serve a dwelling unit shall be permitted to be
\| \| \| \| \| \| \| \| \| \| \| \| \|
of _____ construction? A.non-combustible B. combustible C. rated
\| \| \| \| \| \| \| \|
D. none of the above. - CORRECT ANSWERS ✔✔B. Shall be
\| \| \| \| \| \| \| \| \| \| \|
permitted to be of combustible type UMC Section 602.2 Ex (1)\| \| \| \| \| \| \| \| \| \|
Solid fuel-burning appliances _____ be connected to a venting
\| \| \| \| \| \| \| \| \|
system that serves a gas- or oil-burningappliance.(A) shall (B)
\| \| \| \| \| \| \| \| \|
may (C) shall not(D) with special approval may - CORRECT
\| \| \| \| \| \| \| \| \| \|
ANSWERS ✔✔C. appliances shall not UMC Section 802.5.5.1 \| \| \| \| \| \| \|
Any joint obtained by joining of metal parts with alloys that melt
\| \| \| \| \| \| \| \| \| \| \| \|
at temperatures higher than 840°F, but lowerthan the melting
\| \| \| \| \| \| \| \| \|
temperature of the parts to be joined, is a _____ joint.(A) brazed(B) \| \| \| \| \| \| \| \| \| \| \| \|
fused (D) soldered (C) welded - CORRECT ANSWERS ✔✔A. Is a
\| \| \| \| \| \| \| \| \| \| \|
brazed joint UMC section 2 1 2.0 \| \| \| \| \| \|
