Revit Certification - Practice Test
An electrical designer is creating a receptacle family. The designer wants the receptacle
symbol to appear when the Detail Level is Coarse and Medium, and the receptacle
geometry to appear when the Detail Level is Fine. How can this be accomplished? -
CORRECT ANSWER-Adjust the Detail Levels in the Family Element Visibility Settings
for the geometry
Which tool will save the changes in a local model to the central model? - CORRECT
ANSWER-Synchronize with Central tool
An electrical designer enables Section Box for a 3D view, but the section box is not
visible in the view. Which setting should the designer check? - CORRECT ANSWER-
Visibility/Graphic Overrides
Which parameter will control the elevation of cable trays? - CORRECT ANSWER-
Bottom Elevation
Refer to the exhibit. An electrical designer wants to export a schedule for use in Excel.
When the designer views the export option, it is unavailable. What should the designer
do? - CORRECT ANSWER-Open a schedule view
An electrical designer is working in a project with a linked architectural Revit model. The
designer is unable to select the link. What is causing this condition? - CORRECT
ANSWER-The Select Links option is disabled.
Refer to the exhibit. What kind of views are Level 1 - Area A and Level 1 - Area B? -
CORRECT ANSWER-Dependent views
Refer to the exhibit. An electrical designer opens a panelboard family and sees the
following. What is the hosting type of this family? - CORRECT ANSWER-Face-based
An electrical designer selects a run of conduit and changes the phase status to
demolished. After doing this, an error appears stating that the elements need to be
disconnected. Why does this error occur? - CORRECT ANSWER-Demolished elements
cannot be connected.
When placing electrical equipment, what does pressing the SPACEBAR do? -
CORRECT ANSWER-Rotates the equipment 90 degrees
, When lighting fixtures are placed in a space, which space parameter is calculated
based on the Lumens from each fixture? - CORRECT ANSWER-Average Estimated
Illumination
An electrical designer wants to associate the Elevation from Level parameter for several
receptacles in a project to a single parameter. What type of parameter should the
designer create? - CORRECT ANSWER-Global
An electrical designer creates a sheet using a custom titleblock. The designer wants to
include a parameter to indicate the building area. How can this be accomplished? -
CORRECT ANSWER-Open the titleblock in the Family Editor and add the parameter as
a label.
An electrical designer places hosted lighting fixtures in the ceiling of a linked
architectural model. The designer then removes the linked architectural model. What
happens to the lighting fixtures? - CORRECT ANSWER-The lighting fixtures become
orphaned.
An electrical designer is creating a receptacle family. The designer places an electrical
connector and sets the System Type to Power - Unbalanced. The designer wants to
control the Voltage of the electrical connector in the project. How can this be
accomplished? - CORRECT ANSWER-Associate the Voltage parameter on the
connector to a family parameter.
An electrical designer needs to set the Connection Type for a circuit to Feed Through
Lugs. What does the designer need to do to enable this functionality? - CORRECT
ANSWER-Select the panel and enable Feed Through Lugs in the Properties palette.
Which setting can be used to create a new central model from an existing central
model? - CORRECT ANSWER-Detach from Central
Which tool can be used to tag components that have been selected first? - CORRECT
ANSWER-Tag All Not Tagged
An electrical designer is creating a lighting fixture schedule and wants to include
information from the spaces in which the lighting fixtures are placed. How can this be
accomplished? - CORRECT ANSWER-Choose Space in Select available fields from.
An electrical designer modifies a panel schedule template, but the panel schedules
associated with the template do not update. What should the designer do? - CORRECT
ANSWER-Select the panels in the Manage Panel Schedule Templates dialog and click
Update Schedules.
When hovering the cursor over a component on a circuit, which key can be used to
highlight the circuit? - CORRECT ANSWER-Tab
An electrical designer is creating a receptacle family. The designer wants the receptacle
symbol to appear when the Detail Level is Coarse and Medium, and the receptacle
geometry to appear when the Detail Level is Fine. How can this be accomplished? -
CORRECT ANSWER-Adjust the Detail Levels in the Family Element Visibility Settings
for the geometry
Which tool will save the changes in a local model to the central model? - CORRECT
ANSWER-Synchronize with Central tool
An electrical designer enables Section Box for a 3D view, but the section box is not
visible in the view. Which setting should the designer check? - CORRECT ANSWER-
Visibility/Graphic Overrides
Which parameter will control the elevation of cable trays? - CORRECT ANSWER-
Bottom Elevation
Refer to the exhibit. An electrical designer wants to export a schedule for use in Excel.
When the designer views the export option, it is unavailable. What should the designer
do? - CORRECT ANSWER-Open a schedule view
An electrical designer is working in a project with a linked architectural Revit model. The
designer is unable to select the link. What is causing this condition? - CORRECT
ANSWER-The Select Links option is disabled.
Refer to the exhibit. What kind of views are Level 1 - Area A and Level 1 - Area B? -
CORRECT ANSWER-Dependent views
Refer to the exhibit. An electrical designer opens a panelboard family and sees the
following. What is the hosting type of this family? - CORRECT ANSWER-Face-based
An electrical designer selects a run of conduit and changes the phase status to
demolished. After doing this, an error appears stating that the elements need to be
disconnected. Why does this error occur? - CORRECT ANSWER-Demolished elements
cannot be connected.
When placing electrical equipment, what does pressing the SPACEBAR do? -
CORRECT ANSWER-Rotates the equipment 90 degrees
, When lighting fixtures are placed in a space, which space parameter is calculated
based on the Lumens from each fixture? - CORRECT ANSWER-Average Estimated
Illumination
An electrical designer wants to associate the Elevation from Level parameter for several
receptacles in a project to a single parameter. What type of parameter should the
designer create? - CORRECT ANSWER-Global
An electrical designer creates a sheet using a custom titleblock. The designer wants to
include a parameter to indicate the building area. How can this be accomplished? -
CORRECT ANSWER-Open the titleblock in the Family Editor and add the parameter as
a label.
An electrical designer places hosted lighting fixtures in the ceiling of a linked
architectural model. The designer then removes the linked architectural model. What
happens to the lighting fixtures? - CORRECT ANSWER-The lighting fixtures become
orphaned.
An electrical designer is creating a receptacle family. The designer places an electrical
connector and sets the System Type to Power - Unbalanced. The designer wants to
control the Voltage of the electrical connector in the project. How can this be
accomplished? - CORRECT ANSWER-Associate the Voltage parameter on the
connector to a family parameter.
An electrical designer needs to set the Connection Type for a circuit to Feed Through
Lugs. What does the designer need to do to enable this functionality? - CORRECT
ANSWER-Select the panel and enable Feed Through Lugs in the Properties palette.
Which setting can be used to create a new central model from an existing central
model? - CORRECT ANSWER-Detach from Central
Which tool can be used to tag components that have been selected first? - CORRECT
ANSWER-Tag All Not Tagged
An electrical designer is creating a lighting fixture schedule and wants to include
information from the spaces in which the lighting fixtures are placed. How can this be
accomplished? - CORRECT ANSWER-Choose Space in Select available fields from.
An electrical designer modifies a panel schedule template, but the panel schedules
associated with the template do not update. What should the designer do? - CORRECT
ANSWER-Select the panels in the Manage Panel Schedule Templates dialog and click
Update Schedules.
When hovering the cursor over a component on a circuit, which key can be used to
highlight the circuit? - CORRECT ANSWER-Tab
