BMW ASSOCIATE LEVEL ASE TEST
A lifting pad must be in place to lift a BMW vehicle, T or F? - "CORRECT ANSWER" True
A technician should consider which of the following questions for a quality control process after performing
service work to a vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above - "CORRECT ANSWER" All of the above
According to MSDS warning symbols, the warning symbol with a skull and cross bones shown represents -
"CORRECT ANSWER" Acute toxicity
All BMW special tools are autoship to the dealer.
True or False? - "CORRECT ANSWER" False
All brand new BMW vehicles require a QC1 inspection.
Tech A states that transport Mode should be deleted using ISTA.
Tech B says that transport mode should be deleted using the transport mode switching device. - "CORRECT
ANSWER" Both A and B
All of the following are true concerning the Roundtable, EXCEPT :
, There are 12 shows each year.
Each Roundtable has a bulletin describing the topics.
The Roundtable is accessed through AIR.
Each Roundtable has a quiz - "CORRECT ANSWER" The Roundtable is accessed through AIR.
Battery voltage is not critical when performing a voltage drop on a circuit.
True or False? - "CORRECT ANSWER" Flase
BMW recommends replacing tire at least every 6 years
what resource can you use to determine that the above statement is correct? - "CORRECT ANSWER" Owners
Manual
BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure - "CORRECT ANSWER" Brake pad thickness and tire thread depth
CPO inspections require a minimum tread depth of 3 mm, as measured from the lowest area in the tread. T or
F? - "CORRECT ANSWER" False (from top of wear indicators)
During a CPO inspection, a front brake pad measurement is taken of 4mm on the left inner pad and 7mm on
the left outer pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed specifications.
A lifting pad must be in place to lift a BMW vehicle, T or F? - "CORRECT ANSWER" True
A technician should consider which of the following questions for a quality control process after performing
service work to a vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above - "CORRECT ANSWER" All of the above
According to MSDS warning symbols, the warning symbol with a skull and cross bones shown represents -
"CORRECT ANSWER" Acute toxicity
All BMW special tools are autoship to the dealer.
True or False? - "CORRECT ANSWER" False
All brand new BMW vehicles require a QC1 inspection.
Tech A states that transport Mode should be deleted using ISTA.
Tech B says that transport mode should be deleted using the transport mode switching device. - "CORRECT
ANSWER" Both A and B
All of the following are true concerning the Roundtable, EXCEPT :
, There are 12 shows each year.
Each Roundtable has a bulletin describing the topics.
The Roundtable is accessed through AIR.
Each Roundtable has a quiz - "CORRECT ANSWER" The Roundtable is accessed through AIR.
Battery voltage is not critical when performing a voltage drop on a circuit.
True or False? - "CORRECT ANSWER" Flase
BMW recommends replacing tire at least every 6 years
what resource can you use to determine that the above statement is correct? - "CORRECT ANSWER" Owners
Manual
BMW special took 83 30 0 492 467 can be used during an inspection to measure:
Coolant level
Coolant concentrate
Brake pad thickness and tire thread depth
Air pressure - "CORRECT ANSWER" Brake pad thickness and tire thread depth
CPO inspections require a minimum tread depth of 3 mm, as measured from the lowest area in the tread. T or
F? - "CORRECT ANSWER" False (from top of wear indicators)
During a CPO inspection, a front brake pad measurement is taken of 4mm on the left inner pad and 7mm on
the left outer pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed specifications.
