IICRC RRT Exam Study Guide questions
with correct answers
When row-cutting most commercial tufted carpet for seaming, technicians should use -
correct answersloop-pile or cushion back cutter
Where practical, the industry-preferred method for trimming seam edges is called what? -
correct answersrow cut
What tool should be used to pound down the metal lip of clamp-down transition strip (door
bar)? - correct answersWhite rubber mallet
When sealing a seam, a bead of adhesive is applied to the carpet edge to adhere what two
things? - correct answers1. Primary backing
2. Secondary backing
When sealing seams, to evenly distribute a latex or acrylic sealer on a carpet's cut edge, what
should technicians use? - correct answerstheir thumb and finger
When seaming or sectioning a carpet, technicians should seal each cut edge with acrylic, latex
or thermoplastic adhesive on what styles of carpet? - correct answerson all stretch-in carpet
What is the recommended seam groomer to use immediately following hot-melt seaming? -
correct answersA smooth or paddle roller
When using a knee kicker and carpet awl to lift carpet off tack strip (gripper), the direction of
lift should be what? - correct answersangled towards the wall then upwards
, To prevent delamination while disengaging wet carpet from tack strip (gripper), technicians
should use what? - correct answersA knee kicker working around the entire perimeter
Chalk used in chalk line tools should be what color? - correct answersWhite
When cutting carpet for seaming or sectioning, normally technicians should be careful not cut
what? - correct answersPile yarns
When replacing old clamp-down metal transition that forms a 90º angle, what should be done
to the new metal? - correct answersPounded down to the finished position and cut at a 45
degree angle in a miter box
After carpet cushion (pad, underlay) is removed from wood floors, what should be done with
the remaining staples? - correct answersremoved completely
When power stretching, what is the tool that can be used to simulate a wall where there is no
wall in an open area? - correct answersDead man
What is an essential safety item needed when driving hardened steel nails into concrete -
correct answersSafety glasses
Identify two essential items required for worksite safety: - correct answers1. First aid kit
2. Fire extinguisher
Identify the agency(s) in charge of regulating the use of personal protective equipment (e.g.,
hard hats, knee pads, goggles, respirators). - correct answersOSHA (HSE);(WHS)
with correct answers
When row-cutting most commercial tufted carpet for seaming, technicians should use -
correct answersloop-pile or cushion back cutter
Where practical, the industry-preferred method for trimming seam edges is called what? -
correct answersrow cut
What tool should be used to pound down the metal lip of clamp-down transition strip (door
bar)? - correct answersWhite rubber mallet
When sealing a seam, a bead of adhesive is applied to the carpet edge to adhere what two
things? - correct answers1. Primary backing
2. Secondary backing
When sealing seams, to evenly distribute a latex or acrylic sealer on a carpet's cut edge, what
should technicians use? - correct answerstheir thumb and finger
When seaming or sectioning a carpet, technicians should seal each cut edge with acrylic, latex
or thermoplastic adhesive on what styles of carpet? - correct answerson all stretch-in carpet
What is the recommended seam groomer to use immediately following hot-melt seaming? -
correct answersA smooth or paddle roller
When using a knee kicker and carpet awl to lift carpet off tack strip (gripper), the direction of
lift should be what? - correct answersangled towards the wall then upwards
, To prevent delamination while disengaging wet carpet from tack strip (gripper), technicians
should use what? - correct answersA knee kicker working around the entire perimeter
Chalk used in chalk line tools should be what color? - correct answersWhite
When cutting carpet for seaming or sectioning, normally technicians should be careful not cut
what? - correct answersPile yarns
When replacing old clamp-down metal transition that forms a 90º angle, what should be done
to the new metal? - correct answersPounded down to the finished position and cut at a 45
degree angle in a miter box
After carpet cushion (pad, underlay) is removed from wood floors, what should be done with
the remaining staples? - correct answersremoved completely
When power stretching, what is the tool that can be used to simulate a wall where there is no
wall in an open area? - correct answersDead man
What is an essential safety item needed when driving hardened steel nails into concrete -
correct answersSafety glasses
Identify two essential items required for worksite safety: - correct answers1. First aid kit
2. Fire extinguisher
Identify the agency(s) in charge of regulating the use of personal protective equipment (e.g.,
hard hats, knee pads, goggles, respirators). - correct answersOSHA (HSE);(WHS)
