Tpc 305; Pumps question with answer
The archmedian screw is pumps material by? - -A bolt threaded screw in an
enclosed cylinder or open trough
-If material being pumped needs to remain at a certain temperature ________ pipes
are used - -Insulated
-Centrifugal pumps are good for pumping waste because of - -Low head pumping
requirements and the ability to pass small particles
-Which is the most well suited pump for pumping high viscosity material? - -Positive
displacement pumps
-Greases, heavy mastics, cement, and similar materials are most often pumped by
- -Piston pumps (solids pumping system)
-In a suction lift pump installation... - -The eye of the impeller is above the fluid
-In pumping systems, the sum of the total static head, head loss, and velocity head
is called? - -Total dynamic head (TDH)
-The horsepower input to a centrifugal pump is referred to as? - -Brake horsepower
-Before you can look at specific efficiency curves of a centrifugal pump, you must
first know the ________ and the _________ - -The speed of the shaft; the diameter of
the pumps impeller
-The ________ curve will tell you at what total head the best energy transfer in a
centrifugal pump will take place - -Efficiency
-Multistage pumps build up ______ of the fluid with each stage until the desired
head is reached - -Velocity
-The open impeller is used primarily for pumping fluids containing __________ - -
Large solids
-Wearing rings prevent damage to the _______ and _______ - -Impeller and casing
-Shaft sleeves are designed to protect the shaft from wear by? - -The packing or
seals
-In a lineshaft turbine... - -The bowl surrounds the impeller
-Axial flow propeller Pump bowls have diffuser vanes to? - -Straighten the flow of
fluid into the discharge pipe
-The major difference in axial flow propeller pump and the mix flow propeller pump
is the? - -Impeller
The archmedian screw is pumps material by? - -A bolt threaded screw in an
enclosed cylinder or open trough
-If material being pumped needs to remain at a certain temperature ________ pipes
are used - -Insulated
-Centrifugal pumps are good for pumping waste because of - -Low head pumping
requirements and the ability to pass small particles
-Which is the most well suited pump for pumping high viscosity material? - -Positive
displacement pumps
-Greases, heavy mastics, cement, and similar materials are most often pumped by
- -Piston pumps (solids pumping system)
-In a suction lift pump installation... - -The eye of the impeller is above the fluid
-In pumping systems, the sum of the total static head, head loss, and velocity head
is called? - -Total dynamic head (TDH)
-The horsepower input to a centrifugal pump is referred to as? - -Brake horsepower
-Before you can look at specific efficiency curves of a centrifugal pump, you must
first know the ________ and the _________ - -The speed of the shaft; the diameter of
the pumps impeller
-The ________ curve will tell you at what total head the best energy transfer in a
centrifugal pump will take place - -Efficiency
-Multistage pumps build up ______ of the fluid with each stage until the desired
head is reached - -Velocity
-The open impeller is used primarily for pumping fluids containing __________ - -
Large solids
-Wearing rings prevent damage to the _______ and _______ - -Impeller and casing
-Shaft sleeves are designed to protect the shaft from wear by? - -The packing or
seals
-In a lineshaft turbine... - -The bowl surrounds the impeller
-Axial flow propeller Pump bowls have diffuser vanes to? - -Straighten the flow of
fluid into the discharge pipe
-The major difference in axial flow propeller pump and the mix flow propeller pump
is the? - -Impeller