SACA EXAM QUESTIONS AND
ANSWERS 100% ACCURATE
What is the pressure shown on this gauge?* - ANSWER-500 kPa
What type of wrench is shown?* - ANSWER-Ratchet
What amount of power is used in this circuit?* - ANSWER-96W
What type of geometric tolerance is shown in the feature control frame on this drawing?
- ANSWER-Circularity
A company's Emergency Action Plan (EAP) should include ALL of the following except?
- ANSWER-Machine operation procedures
What action must be taken to correctly position a dial caliper? - ANSWER-Sweep and
rock to the jaws
What type of hand tool has a cross-shaped head to engage and tighten a fastener?* -
ANSWER-Phillips head screwdriver
Which of these activities is considered non-value added activity in a lean manufacturing
environment?*
0/4 - ANSWER-Moving a product from one station to another
What is the tolerance of the width of this part?* - ANSWER-+/-0.1
What do SDS sheets do?* - ANSWER-Specify material hazards.
When a click-type torque wrench clicks at the set point, what do you do to apply the
proper torque? - ANSWER-Stop turning the wrench
What type of hole is identified by the arrow labeled A?* - ANSWER-Blind
What is the measurement shown on this SI dial caliper, in millimeters? - ANSWER-
22.68 mm
What is NOT a step in an electrical Lockout/Tagout procedure?* - ANSWER-Write
safety officer initials on tag
What type of technical drawing shows the features of a 3-dimensional object in 2
dimensions as seen from different sides of the object? - ANSWER-Multiview drawing
, What is the measurement shown on this micrometer in millimeters? - ANSWER-39.21
What type of logic does this schematic represent? - ANSWER-AND
Which of these components is used to keep the motor turned on after the start
pushbutton is momentarily activated? - ANSWER-CR1A
What component does the schematic represent?* - ANSWER-Pneumatic motor
What type of information would not normally be found in a drawing's title block?*
0/4 - ANSWER-General notes
What machine can be programmed to perform tasks in many different operations? -
ANSWER-Robot
What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 - ANSWER-metal
Which of these is NOT a primary goal of a lean manufacturing system? - ANSWER-
Greater production volume
In the bolt designation shown, what is the pitch? - ANSWER-2.5
What air pressure should be used when compressed air is used to clean or blow parts?
- ANSWER-Below 30 psi
If a machine stops unexpectedly due to a fault, which message tells you only that the
machine has a fault? - ANSWER-Warning message
What material condition does LMC define?* - ANSWER-Condition with the smallest
amount of material
What method do most small air compressors use to compress air - ANSWER-Piston
movement
If an electronic sensor has a PNP type transistor, what effect does that have on the
sensor's operations? - ANSWER-Output signal goes high when the sensor is triggered.
What is used to calibrate a precision measuring instrument?* - ANSWER-Gauge block
What is the scale of the drawing if the actual length of this part is 300 mm and
dimension shown by X measures 50 mm on the drawing? - ANSWER-1:6
In addition to a material block, what is another way a technical drawing can identify the
type of material used to make the drawn object? - ANSWER-Local note
ANSWERS 100% ACCURATE
What is the pressure shown on this gauge?* - ANSWER-500 kPa
What type of wrench is shown?* - ANSWER-Ratchet
What amount of power is used in this circuit?* - ANSWER-96W
What type of geometric tolerance is shown in the feature control frame on this drawing?
- ANSWER-Circularity
A company's Emergency Action Plan (EAP) should include ALL of the following except?
- ANSWER-Machine operation procedures
What action must be taken to correctly position a dial caliper? - ANSWER-Sweep and
rock to the jaws
What type of hand tool has a cross-shaped head to engage and tighten a fastener?* -
ANSWER-Phillips head screwdriver
Which of these activities is considered non-value added activity in a lean manufacturing
environment?*
0/4 - ANSWER-Moving a product from one station to another
What is the tolerance of the width of this part?* - ANSWER-+/-0.1
What do SDS sheets do?* - ANSWER-Specify material hazards.
When a click-type torque wrench clicks at the set point, what do you do to apply the
proper torque? - ANSWER-Stop turning the wrench
What type of hole is identified by the arrow labeled A?* - ANSWER-Blind
What is the measurement shown on this SI dial caliper, in millimeters? - ANSWER-
22.68 mm
What is NOT a step in an electrical Lockout/Tagout procedure?* - ANSWER-Write
safety officer initials on tag
What type of technical drawing shows the features of a 3-dimensional object in 2
dimensions as seen from different sides of the object? - ANSWER-Multiview drawing
, What is the measurement shown on this micrometer in millimeters? - ANSWER-39.21
What type of logic does this schematic represent? - ANSWER-AND
Which of these components is used to keep the motor turned on after the start
pushbutton is momentarily activated? - ANSWER-CR1A
What component does the schematic represent?* - ANSWER-Pneumatic motor
What type of information would not normally be found in a drawing's title block?*
0/4 - ANSWER-General notes
What machine can be programmed to perform tasks in many different operations? -
ANSWER-Robot
What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 - ANSWER-metal
Which of these is NOT a primary goal of a lean manufacturing system? - ANSWER-
Greater production volume
In the bolt designation shown, what is the pitch? - ANSWER-2.5
What air pressure should be used when compressed air is used to clean or blow parts?
- ANSWER-Below 30 psi
If a machine stops unexpectedly due to a fault, which message tells you only that the
machine has a fault? - ANSWER-Warning message
What material condition does LMC define?* - ANSWER-Condition with the smallest
amount of material
What method do most small air compressors use to compress air - ANSWER-Piston
movement
If an electronic sensor has a PNP type transistor, what effect does that have on the
sensor's operations? - ANSWER-Output signal goes high when the sensor is triggered.
What is used to calibrate a precision measuring instrument?* - ANSWER-Gauge block
What is the scale of the drawing if the actual length of this part is 300 mm and
dimension shown by X measures 50 mm on the drawing? - ANSWER-1:6
In addition to a material block, what is another way a technical drawing can identify the
type of material used to make the drawn object? - ANSWER-Local note
