NICET Level III Inspection, Testing, and
Maintenance of Water Based Systems Practice Test.
/ Expert Verified Actual Questions & Answers for
Guaranteed Pass | Newest Update, 2025-2026
Terms in this set (133)
The inspection of a fire C) To keep the pump from over heating and damaging
pump circulation relief component systems D) Water is flowing thru it properly
valve verifies which two
situations? (Choose two).
A). To avoid over
pressurizing the system. B).
To ensure all air is
released from the pump
head.
C). To keep the pump from
over heating and damaging
components.
D). Water is flowing thru it
properly
,Pressure readings for a A) At the hydraulically most remote nozzle
water spray system shall be
made to ensure that water
flow is not impeded by
partially closed valves or
plugged nozzles? At what
point must this reading be
taken? A). At the
hydraulically most remote
nozzle.
B). At the most remote
nozzle in the system.
C). At the nozzle in the
mid point of the system.
D). At three random
nozzles
NICET III Practice
Questions
B)50.
On a hydrostatic test of a
standpipe where the where
the maximum
pressure is in excess of
150psi, which pressure
would the inspector add to
the maximum pressure to
get the hydrostatic test
pressure? A) 25.
B) 50.
C) 100.
D) 150
,Which three of the following A) Check and clean screens and filters. B) Drain water from low
operations should be points
included when restoring a D) Replace plugs or caps on auxiliary drains.
water mist system to service
following a test (choose
3).
A) Check and clean
screens and filters. B)
Drain water from low
points.
C). Lubricate valve seats.
D) Replace plugs or caps on
auxiliary drains
At which two locations can a C) The low point drain for each standpipe.
main drain test be performed D) The main drain test connection
on a standpipe system?
(Choose two).
A) The hose valve on
thefirst floor.
B) The hydraulically
mostremote hose valve.
C) The low point drain
foreach standpipe.
D) The main drain
testconnection
, How frequently should the C) Every 5 years
Mercury level gauge on a
tank Be tested in order to
determine if the gauge is
accurate?
A) Annually.
B) Every 3 years.
C) Every 5 years.
D). Every 10 years
How often shall water level C) Every 5 years
indicators in water tanks be
tested for accuracy?
A) every 2 years.
B) Every 3 years.
C) Every 5 years.
D). Every 7 years
Which 2 pieces of A). Discharge pressure. B). Suction pressure
information are obtained
and recorded in order to
plot test data on a graph
after a pump test?
A). Discharge pressure.
B). Suction pressure
C) type of motor
D) Volts and Amps
Maintenance of Water Based Systems Practice Test.
/ Expert Verified Actual Questions & Answers for
Guaranteed Pass | Newest Update, 2025-2026
Terms in this set (133)
The inspection of a fire C) To keep the pump from over heating and damaging
pump circulation relief component systems D) Water is flowing thru it properly
valve verifies which two
situations? (Choose two).
A). To avoid over
pressurizing the system. B).
To ensure all air is
released from the pump
head.
C). To keep the pump from
over heating and damaging
components.
D). Water is flowing thru it
properly
,Pressure readings for a A) At the hydraulically most remote nozzle
water spray system shall be
made to ensure that water
flow is not impeded by
partially closed valves or
plugged nozzles? At what
point must this reading be
taken? A). At the
hydraulically most remote
nozzle.
B). At the most remote
nozzle in the system.
C). At the nozzle in the
mid point of the system.
D). At three random
nozzles
NICET III Practice
Questions
B)50.
On a hydrostatic test of a
standpipe where the where
the maximum
pressure is in excess of
150psi, which pressure
would the inspector add to
the maximum pressure to
get the hydrostatic test
pressure? A) 25.
B) 50.
C) 100.
D) 150
,Which three of the following A) Check and clean screens and filters. B) Drain water from low
operations should be points
included when restoring a D) Replace plugs or caps on auxiliary drains.
water mist system to service
following a test (choose
3).
A) Check and clean
screens and filters. B)
Drain water from low
points.
C). Lubricate valve seats.
D) Replace plugs or caps on
auxiliary drains
At which two locations can a C) The low point drain for each standpipe.
main drain test be performed D) The main drain test connection
on a standpipe system?
(Choose two).
A) The hose valve on
thefirst floor.
B) The hydraulically
mostremote hose valve.
C) The low point drain
foreach standpipe.
D) The main drain
testconnection
, How frequently should the C) Every 5 years
Mercury level gauge on a
tank Be tested in order to
determine if the gauge is
accurate?
A) Annually.
B) Every 3 years.
C) Every 5 years.
D). Every 10 years
How often shall water level C) Every 5 years
indicators in water tanks be
tested for accuracy?
A) every 2 years.
B) Every 3 years.
C) Every 5 years.
D). Every 7 years
Which 2 pieces of A). Discharge pressure. B). Suction pressure
information are obtained
and recorded in order to
plot test data on a graph
after a pump test?
A). Discharge pressure.
B). Suction pressure
C) type of motor
D) Volts and Amps
