• ¿Documento equivocado? Cámbialo gratis
  • Escrito por estudiantes que aprobaron
  • Inmediatamente disponible después del pago
  • Leer en línea o como PDF
Vender
¿Dónde estudias?
Tu idioma
Document preview thumbnail
Vista previa 3 fuera de 22 páginas
Examen

ASNT Level 3 Basic Materials & Processes

Document preview thumbnail
Vista previa 3 fuera de 22 páginas

ASNT Level 3 Basic Materials & Processes

Vista previa del contenido

ASNT Level 3 Basic Materials & Processes
Study online at https://quizlet.com/_51unos

1. Fracture is a type of material failure. Of the following Permanent deformation.
which is another type of material failure?

2. Which of the following statements best differentiates Discontinuities can propa-
between a defect and a discontinuity? gate and become defects.

3. Nondestructive testing is often differentiated from NDT involves indirect tests
other measurements or inspection techniques in that: related to some other
quality or characteristic of
material.

4. What are the functions of NDT? Identifying and sorting of
material.
Identifying of material
properties.
Ensuring absence of faults
or defects that could cause
a part to fail.

5. An important basis for the success of fracture control The need to ensure that
design procedures is: unexpected flaws of some
critical size are not present
when the component en-
ters service.

6. If properly used, NDT can assist in fracture control by: Providing an accurate
evaluation of the number
and type of discontinuities
that exist in a material .

7. A statement that a particular experiment produced There is a 5% probability
a 0.9 probability of detection with a 95% confidence that the probability of de-
level means that: tection is overstated.


, ASNT Level 3 Basic Materials & Processes
Study online at https://quizlet.com/_51unos


8. Most solid metals and plastics that have reasonable Engineering materials.
strength at room temperature are called:

9. Material properties, as used in design, are most fre- Materials testing.
quently determined by:

10. Even at the early stages of product planning, NDT The design of the part
should be considered because: should permit easy access
to critical areas for later in-
spection.

11. which of the following material properties are of most Chemical properties.
concern if corrosion resistance is essential?

12. Which of the following is true relative to the compar- Iron can exist in several
ison of the properties of aluminum-based alloys and different crystalline struc-
iron-based alloys? tures and its properties
can be controlled by heat
treatment.

13. Tensile test are conducted on specimens from a newly Destructive tests.
developed alloy in order to determine the ultimate
tensile strength of the material. Such tests are re-
ferred to as:

14. A bar that is 2 in. long, 2 in. wide and 1 in. thick is 18000 psi.
subjected to a tensile load acting along the lenght of
the bar of 36000 lbs. What is the tensle stress within
the bar?

15. What is Point B on the Stress-Strain diagram where it Elastic limit.
first starts to curve?



, ASNT Level 3 Basic Materials & Processes
Study online at https://quizlet.com/_51unos

16. Stress-Strain diagram, which of the following ranges Deformation rate to the ul-
indicates the affect of work hardening, to its maxi- timate strength
mum, caused by plastic flow of the material during a
tensile load?

17. On the Stress-Strain diagram, the points represented Less ductile.
by E and F would be closer together if the material
being tested were:

18. The modules of elasticity, or Young's modules, is relat- Stiffness and yield
ed to the material's relative: strength.

19. Which of the following materials is typically consid- Cast iron.
ered when the application only requires high com-
pressive strength?

20. A fatigue failure can often be prevented by using NDT Detect surface discontinu-
to: ities that could be stress
risers.

21. Which of the following tests uses a pendulum to break Charpy test.
a specimen that is notched and supported on both
ends, with the results of measuring energy absorp-
tion?

22. What is a S-N curve? An endurance limit curve
diagram.

23. Direct hardness test provide a measure of a material's Surface and near-surface
ability to resist: penetration.

24. Under ordinary usage, metals exist as: Crystalline solids.

25.

Información del documento

Subido en
16 de febrero de 2025
Número de páginas
22
Escrito en
2024/2025
Tipo
Examen
Contiene
Preguntas y respuestas
$16.99

¿Documento equivocado? Cámbialo gratis Dentro de los 14 días posteriores a la compra y antes de descargarlo, puedes elegir otro documento. Puedes gastar el importe de nuevo.
Escrito por estudiantes que aprobaron
Inmediatamente disponible después del pago
Leer en línea o como PDF

Seller avatar
Los indicadores de reputación están sujetos a la cantidad de artículos vendidos por una tarifa y las reseñas que ha recibido por esos documentos. Hay tres niveles: Bronce, Plata y Oro. Cuanto mayor reputación, más podrás confiar en la calidad del trabajo del vendedor.
Classroom001
4.3
(3)
Vendido
22
Seguidores
8
Artículos
602
Última venta
11 meses hace



Por qué los estudiantes eligen Stuvia

Creado por compañeros estudiantes, verificado por reseñas

Calidad en la que puedes confiar: escrito por estudiantes que aprobaron y evaluado por otros que han usado estos resúmenes.

¿No estás satisfecho? Elige otro documento

¡No te preocupes! Puedes elegir directamente otro documento que se ajuste mejor a lo que buscas.

Paga como quieras, empieza a estudiar al instante

Sin suscripción, sin compromisos. Paga como estés acostumbrado con tarjeta de crédito y descarga tu documento PDF inmediatamente.

Student with book image

“Comprado, descargado y aprobado. Así de fácil puede ser.”

Alisha Student

Preguntas frecuentes