Name: Score:
342 Multiple choice questions
Term 1 of 342
How are metric tapers designated?
As a ratio 1:2
As a ratio 1:25
As a ratio 1:15
The lap
Term 2 of 342
An out of balance wheel:
vibrates
lowers symmetrically
goggles
longitudinal
Term 3 of 342
What is the minimum safe distance from which an electric arc should be seen with the naked
eye?
4:1 or 75.5 degrees L/4=S
wire wheel
12M (40ft)
1/4" per foot
,Term 4 of 342
What does the fire triangle consist of?
Access and working
Kept clean and oiled
The table can be swivelled
Heat, fuel and oxygen
Term 5 of 342
If the lines are scribed onto a workpiece it is considered to be:
wire wheel
fixed and not changeable
the operator
temporary layout
Term 6 of 342
What is the main purpose of stop blocks?
Align the workpiece with the milling cutter.
Guide the workpiece into the cutting tool.
Support the weight of the machine during operation.
Stop the workpiece from shifting under load
Term 7 of 342
What type of chisel would be used to cut a narrow square shaped groove in a piece of mild
steel?
aluminum oxide
Acetylene
Cape chisel
It can only cut straight
,Term 8 of 342
What classification of ladders may be used for construction purposes?
82 degrees
Grade 3
Buffer
3 teeth
Term 9 of 342
The most common lathe operation is:
milling
turning
coughing
rolling
Term 10 of 342
Copper sulphate layout solution should be used on:
Ferrous metals
Copper
Aluminum
C= basic open hearth carbon steel
Term 11 of 342
What is the recommended speed to run a grinding wheel?
Never run it faster that the max RPM of the grinding wheel
Run it continuously without stopping to maintain performance
Use it at a speed that feels comfortable to the operator
Always operate it at twice the recommended rpm for efficiency
, Term 12 of 342
When tapping a hole with a pipe tap, how many threads of the nipple should be able to turn
into the hole before the use of a wrench becomes necessary?
2-3 threads
Tailstock clamp
75 percent
Neutral
Term 13 of 342
What is a worker responsible for?
For own safety
Wear proper PPE
Not remove any safeties
Have proper instruction of a piece of equipment
Use tools properly
1. Unilateral
2. Bilateral
3. Direct
Compares 2 sets of graduations to magnify the accuracy of the measuerment
1. Overload 2. Overcurrent 3. Ground fault protection
Term 14 of 342
Before using a gauge block, you should take which of the following actions?
Kept clean and oiled
1. Overload 2. Overcurrent 3. Ground fault protection
Inspect and clean shaft area
Remove the rust preventative compound
342 Multiple choice questions
Term 1 of 342
How are metric tapers designated?
As a ratio 1:2
As a ratio 1:25
As a ratio 1:15
The lap
Term 2 of 342
An out of balance wheel:
vibrates
lowers symmetrically
goggles
longitudinal
Term 3 of 342
What is the minimum safe distance from which an electric arc should be seen with the naked
eye?
4:1 or 75.5 degrees L/4=S
wire wheel
12M (40ft)
1/4" per foot
,Term 4 of 342
What does the fire triangle consist of?
Access and working
Kept clean and oiled
The table can be swivelled
Heat, fuel and oxygen
Term 5 of 342
If the lines are scribed onto a workpiece it is considered to be:
wire wheel
fixed and not changeable
the operator
temporary layout
Term 6 of 342
What is the main purpose of stop blocks?
Align the workpiece with the milling cutter.
Guide the workpiece into the cutting tool.
Support the weight of the machine during operation.
Stop the workpiece from shifting under load
Term 7 of 342
What type of chisel would be used to cut a narrow square shaped groove in a piece of mild
steel?
aluminum oxide
Acetylene
Cape chisel
It can only cut straight
,Term 8 of 342
What classification of ladders may be used for construction purposes?
82 degrees
Grade 3
Buffer
3 teeth
Term 9 of 342
The most common lathe operation is:
milling
turning
coughing
rolling
Term 10 of 342
Copper sulphate layout solution should be used on:
Ferrous metals
Copper
Aluminum
C= basic open hearth carbon steel
Term 11 of 342
What is the recommended speed to run a grinding wheel?
Never run it faster that the max RPM of the grinding wheel
Run it continuously without stopping to maintain performance
Use it at a speed that feels comfortable to the operator
Always operate it at twice the recommended rpm for efficiency
, Term 12 of 342
When tapping a hole with a pipe tap, how many threads of the nipple should be able to turn
into the hole before the use of a wrench becomes necessary?
2-3 threads
Tailstock clamp
75 percent
Neutral
Term 13 of 342
What is a worker responsible for?
For own safety
Wear proper PPE
Not remove any safeties
Have proper instruction of a piece of equipment
Use tools properly
1. Unilateral
2. Bilateral
3. Direct
Compares 2 sets of graduations to magnify the accuracy of the measuerment
1. Overload 2. Overcurrent 3. Ground fault protection
Term 14 of 342
Before using a gauge block, you should take which of the following actions?
Kept clean and oiled
1. Overload 2. Overcurrent 3. Ground fault protection
Inspect and clean shaft area
Remove the rust preventative compound