EUNICE
Mech Test Elevator WITH 100% SURE ANSWERS
Terms in this set (184)
RPM formula 60 x (Frequency) / (P/2)
# of counterweights formula
CWT Governor Tripping Speed Tripping speed should be 10% Higher then Car Govt Tripping Speed
Generally weight of the car plus 40% of capacity load. EX. 5000lb car with 2000lb
Total CWT weight equals?
capacity. CWT = 5k + 800(40% x 2k) = 5800
ExI
Watts (P) RxI^2
E^2/R
RxI
Volts (E) P/I
Square root of PxR
Sqr Root of P/R
Amps (I) P/E
E/R
P/I^2
Ohms (R) E^2/P
E/I
Inverter
And
Or
1/7
, Nand
Nor
Exclusive Or
You've been provided with an unfamiliar SDS
brand of solvent. What is the best source
for information on it?
A ladder needs to extend 20' from the floor 5', base always 1/4 of the distance from wall to base.
to next landing. How far from the wall
should the base be?
How would you get into a pit to service an Operate the bottom hoist way access switch
elevator buffer?
ASME A17.1 Code states you must have Pit Switch and Light Switch
what two things in the pit?
What prevents planks from slipping? Cleats nailed to the underside of the plank
What is best used for determining the A plumb line.
correct rope drop from the machine drive
sheave to the hitch plate?
Valve spring is shown at 1 3/8" and the 5 1/2. 1 3/8 x 4 is 4 and 24/16 or 5 and 8/16 or 1/2
drawing scale is 1 to 4. What is the actual
size?
Standard Rail is how many feet? 16'
1 cm = .3937"
A safety hitch connecting arm's dimensions 1 1/4 = 1.25"
are 1 1/4". What is the metric equivalent?
so 1.25/.3937 = 3.175 cm
A moving walk layout indicates a clearance 1mm = .03937"
of 6.5 mm for a pallet roller. What
dimension would you read in inches on 6.5 (.03937)= .256"
your ruler?
You're assembling a CWT in the pit with the The factors here are Stretch, Buffer and stand height, and Runby.
following parameters. Buffer 3' or 36"
Cable Length 175' Runby 10'
Rope stretch 12"/100' Rope stretch is 21". 12" per 100' (175 is 100+75, so 12"+9")
Height of buffer and stand 3' Total is 67"
CWT runby 10'
Pit Depth 6'
At what height will you block the CWT?
Drilling a hole into a machine beam, what Center Punch
can you use to prevent the drill bit from
walking?
2/7
Mech Test Elevator WITH 100% SURE ANSWERS
Terms in this set (184)
RPM formula 60 x (Frequency) / (P/2)
# of counterweights formula
CWT Governor Tripping Speed Tripping speed should be 10% Higher then Car Govt Tripping Speed
Generally weight of the car plus 40% of capacity load. EX. 5000lb car with 2000lb
Total CWT weight equals?
capacity. CWT = 5k + 800(40% x 2k) = 5800
ExI
Watts (P) RxI^2
E^2/R
RxI
Volts (E) P/I
Square root of PxR
Sqr Root of P/R
Amps (I) P/E
E/R
P/I^2
Ohms (R) E^2/P
E/I
Inverter
And
Or
1/7
, Nand
Nor
Exclusive Or
You've been provided with an unfamiliar SDS
brand of solvent. What is the best source
for information on it?
A ladder needs to extend 20' from the floor 5', base always 1/4 of the distance from wall to base.
to next landing. How far from the wall
should the base be?
How would you get into a pit to service an Operate the bottom hoist way access switch
elevator buffer?
ASME A17.1 Code states you must have Pit Switch and Light Switch
what two things in the pit?
What prevents planks from slipping? Cleats nailed to the underside of the plank
What is best used for determining the A plumb line.
correct rope drop from the machine drive
sheave to the hitch plate?
Valve spring is shown at 1 3/8" and the 5 1/2. 1 3/8 x 4 is 4 and 24/16 or 5 and 8/16 or 1/2
drawing scale is 1 to 4. What is the actual
size?
Standard Rail is how many feet? 16'
1 cm = .3937"
A safety hitch connecting arm's dimensions 1 1/4 = 1.25"
are 1 1/4". What is the metric equivalent?
so 1.25/.3937 = 3.175 cm
A moving walk layout indicates a clearance 1mm = .03937"
of 6.5 mm for a pallet roller. What
dimension would you read in inches on 6.5 (.03937)= .256"
your ruler?
You're assembling a CWT in the pit with the The factors here are Stretch, Buffer and stand height, and Runby.
following parameters. Buffer 3' or 36"
Cable Length 175' Runby 10'
Rope stretch 12"/100' Rope stretch is 21". 12" per 100' (175 is 100+75, so 12"+9")
Height of buffer and stand 3' Total is 67"
CWT runby 10'
Pit Depth 6'
At what height will you block the CWT?
Drilling a hole into a machine beam, what Center Punch
can you use to prevent the drill bit from
walking?
2/7