• ¿Documento equivocado? Cámbialo gratis
  • Escrito por estudiantes que aprobaron
  • Inmediatamente disponible después del pago
  • Leer en línea o como PDF
Vender
¿Dónde estudias?
Tu idioma
Document preview thumbnail
Vista previa 2 fuera de 6 páginas
Examen

Backflow Prevention Assembly Tester Training.

Document preview thumbnail
Vista previa 2 fuera de 6 páginas

Backflow Prevention Assembly Tester Training.

Vista previa del contenido

Backflow Prevention Assembly Tester
Training
What is the difference between CV 1 and CV 2 on a double CV assembly - ANS-The
two CV operate the same

In a perfect vacuum, water can be drawn up a column__________feet. - ANS-33.9

Which of the following is considered to be a chemical contaminant? - ANS-Arsenic

Which of the following is considered to be a biological health hazard? - ANS-Giardia

What type of assembly has two internally spring- loaded CV, two shut- off valves, and
four test cocks? - ANS-Double Check

Which of the following is the most suitable protection when directly connecting potable
water supply lines to sewerage systems or to radioactive sources? - ANS-Air Gap

A Bypass of a Backflow prevention assembly may be permitted only if the assembly in
the bypass: - ANS-Is the same type

What Federal Law made water purveyors responsible for water quality all the way to the
customers tap? - ANS-Safe Drinking Water Act Amendment of 1986

If a column of water is exerting a pressure of 50 psi, how high must the water be inside
the column? - ANS-115.5ft

As the velocity of water increases, pressure: - ANS-Decreases

Atmospheric pressure at sea level is _____psi - ANS-14.7

A water supply other than the purveyors approved supply that is available to a premise
is called: - ANS-Auxiliary Water Supply

When testing a DCDA the mainline and bypass assemblies should be a tested minimum
of ________ months. - ANS-12

How can backsiphonage action be broken - ANS-Air Gap

, What single difficult to regulate item is more commonly associated with cross
connections, specifically through backsiphonage? - ANS-Garden Hose

Which device must have proper drainage provided for all enclosures? - ANS-Reduced
pressure Backflow preventer

The appropriate height for an Air Gap is : - ANS-2x pipe size Diameter above flood rim
of the receiving vessel, minimum of 1"

While testing CV 1 on a dc, water recedes from the sight tube attached to TC3. The
gauge should be moved to the centerline of the assembly and the static pressure drop
across CV 1 should be recorded. What other information should be recorded? -
ANS-CV2 is leaking and shutoff valve 2 is leaking

At what point is the relief valve in a RP required to open? - ANS-2.0psid

What is the minimum spring tension recommended on CV1 in a RPZ? - ANS-3 psi
greater than the tension recommended on CV1 in a RPZ

Which device protects against back pressure and backsiphonage? - ANS-Reduced
pressure Backflow preventer

While testing the air inlet valve on a spill proof vacuum breaker, the high side bleed
needle valve may need to be opened more than 1/4 turn in order to allow the air inlet to
open? What is the likely cause? - ANS-Leaking shutoff valve #1

According to USC, what is the correct height for installing a RPZ? - ANS-12 inches
above grade, but no more than 36inches

What is the correct height to install a PVB? - ANS-12inches above the highest
downstream point

What company or agency is responsible for testing and approving all Backflow
prevention assemblies in the US? - ANS-Foundation for Cross Connection Control &
Hydraulic Research

Backflow Prevention assemblies are often installed in parallel in order to: -
ANS-Maintain service during testing and repairs

Información del documento

Estudio
Subido en
14 de junio de 2024
Número de páginas
6
Escrito en
2023/2024
Tipo
Examen
Contiene
Preguntas y respuestas
$8.49

¿Documento equivocado? Cámbialo gratis Dentro de los 14 días posteriores a la compra y antes de descargarlo, puedes elegir otro documento. Puedes gastar el importe de nuevo.
Escrito por estudiantes que aprobaron
Inmediatamente disponible después del pago
Leer en línea o como PDF

Seller avatar
Los indicadores de reputación están sujetos a la cantidad de artículos vendidos por una tarifa y las reseñas que ha recibido por esos documentos. Hay tres niveles: Bronce, Plata y Oro. Cuanto mayor reputación, más podrás confiar en la calidad del trabajo del vendedor.
Ace360PRO
4.7
(108)
Vendido
262
Seguidores
3
Artículos
10566
Última venta
1 mes hace



Por qué los estudiantes eligen Stuvia

Creado por compañeros estudiantes, verificado por reseñas

Calidad en la que puedes confiar: escrito por estudiantes que aprobaron y evaluado por otros que han usado estos resúmenes.

¿No estás satisfecho? Elige otro documento

¡No te preocupes! Puedes elegir directamente otro documento que se ajuste mejor a lo que buscas.

Paga como quieras, empieza a estudiar al instante

Sin suscripción, sin compromisos. Paga como estés acostumbrado con tarjeta de crédito y descarga tu documento PDF inmediatamente.

Student with book image

“Comprado, descargado y aprobado. Así de fácil puede ser.”

Alisha Student

Preguntas frecuentes