• ¿Documento equivocado? Cámbialo gratis
  • Escrito por estudiantes que aprobaron
  • Inmediatamente disponible después del pago
  • Leer en línea o como PDF
Vender
¿Dónde estudias?
Tu idioma
Document preview thumbnail
Vista previa 2 fuera de 12 páginas
Examen

Millwright Practice Exam 2 Already Solved 100%

Document preview thumbnail
Vista previa 2 fuera de 12 páginas

unusual - Answer If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator sharpened brass putty knife - Answer For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended Conducted on the job - Answer Apprenticeship training is_______ distance - Answer Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for the indicator readings and into whole inches horizontally for the__________ hidden - Answer The orthographic drawing may contain a dashed or _______ line Radiation - Answer In order to shoot through a test object and project an image onto a detector or a sheet of film, radiography uses a source of penetrating called _______ *scribe circles *transfer measurements *compare distances measure angles - Answer Which of the following task would you not perform with dividers? 10% - Answer The over speed trip device is actuated when the turbine reaches a predetermined limit usually _________% above normal full-load speed high - Answer Positive results in an offset measurement mean that the MTBM is _____ or on the 3-o'clock side. offset misalignment - Answer The coupling gap is set, and then the ______ is measured pressure - Answer In a hydraulic system, movement depends on_____ furniture or utility items - Answer Fractional dimensions are used on objects such as _______ or ______ elimination - Answer If the cause of the problem is not immediately understood, the process of________is often the procedure of choice 3/16 - Answer When applying sealant to the sealing gland flanges, keep the sealant away from the inside edges of the flange by at least_______ inch Transducer - Answer A stroboscope is triggered by a_______ thread - Answer The pitch of threaded fasteners is measured with a ________gauge Surface cracks - Answer Liquid penetrant highlights flaws and reveals________ die - Answer A tool used to cut external threats on s bolt or rod is called a ______ special processes - Answer A bill of materials may include info on _______ and other reference information surface speed - Answer Engaged gears always have the same _____ general arrangement - Answer Elevation of equipment is usually found in the_____ Vibrations - Answer Inspect the pulleys, rollers, and idlers for unevenness or______ 15-20 degree angle - Answer When cutting thin steel with Oxyfuel fuel cutting equipment, hold the torch so that the tip is pointing in the direction the torch is traveling at a _____ angle Grease......... - Answer Labby seals work BEST with materials such as_____ Friction - Answer Lubrication is the application of any substance that reduces________ Driver coupling jig - Answer When the dial indicator is mounted on the complex reverse driven coupling jig , the indicator is registered on the____ In racks - Answer Pipe should be stored_____ Single deep groove radial - Answer The most common type of ball bearing is a _____ bearing split - Answer Couplings that are installed after the driver and driven shafts have been aligned and the equipment has been fastened into position are ________ couplings Factors - Answer When two or more numbers are multiplied to make another number thy ate called _______of the third number clockwise - Answer The continuous-reading dial indicator starts at zero and increases _________ Electronic filters - Answer Vibration within a specific narrow band range can be detected by _______ Teflon - Answer What type of o ring do you use with temperatures between-300 and 500? Rivet cutting - Answer The special cutting til for cutting off bolt heads and nuts is called a ______ tip pressure - Answer PCVs limit and regulate _______in the system Displacement - Answer The total distance the shaft travels from one peak to the other during one vibration cycle is the ______ Cup - Answer A positive-contact seal, generally used on cylinder pistons is the ______seal Brass plugs - Answer Equipment reference points are marked with_____ marring - Answer On a hydraulic press, use a piece of material softer than the work piece to keep from________ the work piece Exact bottom - Answer When setting up an angle iron jig, one indicator should be on the exact top of the MTBM, and the other indicator should be positioned at the ______ of the driven shaft A broken cam - Answer A pillow block barring failure that is caused by an undersized shaft is _______ Excessive leakage - Answer The most common symptom of packing failure is ________ filter - Answer The abbreviation FLT on a hydraulic drawing means _____ Lifting rough castings - Answer Chain slings are normally used for_________ Angle Dimensions - Answer Curved lines with arrowheads touching the extension lines are _________ Replacing damaged rollers - Answer Maintaining and repairing roller conveyors consists mainly of ________ Indicator sag - Answer When fabricating a jig, the millwright should minimize __________ Airfoil - Answer Air flows through the wheel with less turbulence in a __________ centrifugal fan


Información del documento

Subido en
9 de septiembre de 2023
Número de páginas
12
Escrito en
2023/2024
Tipo
Examen
Contiene
Preguntas y respuestas
$11.99

¿Documento equivocado? Cámbialo gratis Dentro de los 14 días posteriores a la compra y antes de descargarlo, puedes elegir otro documento. Puedes gastar el importe de nuevo.
Escrito por estudiantes que aprobaron
Inmediatamente disponible después del pago
Leer en línea o como PDF

Seller avatar
Los indicadores de reputación están sujetos a la cantidad de artículos vendidos por una tarifa y las reseñas que ha recibido por esos documentos. Hay tres niveles: Bronce, Plata y Oro. Cuanto mayor reputación, más podrás confiar en la calidad del trabajo del vendedor.
Grademasters
3.8
(46)
Vendido
118
Seguidores
69
Artículos
2591
Última venta
1 mes hace




Por qué los estudiantes eligen Stuvia

Creado por compañeros estudiantes, verificado por reseñas

Calidad en la que puedes confiar: escrito por estudiantes que aprobaron y evaluado por otros que han usado estos resúmenes.

¿No estás satisfecho? Elige otro documento

¡No te preocupes! Puedes elegir directamente otro documento que se ajuste mejor a lo que buscas.

Paga como quieras, empieza a estudiar al instante

Sin suscripción, sin compromisos. Paga como estés acostumbrado con tarjeta de crédito y descarga tu documento PDF inmediatamente.

Student with book image

“Comprado, descargado y aprobado. Así de fácil puede ser.”

Alisha Student

Preguntas frecuentes

Ups! No podemos cargar tu documento ahora. Inténtalo de nuevo o contacta con soporte.