AND CORRECT ANSWERS (VERIFIED ANSWERS)
Q&A 2027 |INSTANT DOWNLOAD PDF
1. What is the primary responsibility of an electrical
inspector?
A. Design electrical systems B. Verify that electrical installations
comply with applicable codes C. Install electrical equipment D.
Sell electrical materials
Correct Answer: B. Verify that electrical installations comply
with applicable codes.
Rationale: Electrical inspectors examine installations to ensure
compliance with adopted electrical codes and applicable safety
requirements.
2. What is the primary purpose of the National Electrical Code
(NEC)?
A. Establish electrical equipment prices B. Provide rules for safe
electrical installations C. Train electricians in business
management D. Regulate electricity billing
Correct Answer: B. Provide rules for safe electrical installations.
Rationale: The NEC establishes minimum safety requirements
for electrical installations to protect people and property from
electrical hazards.
,3. Which organization publishes the National Electrical Code?
A. OSHA B. IEEE C. NFPA D. ANSI
Correct Answer: C. NFPA.
Rationale: The National Fire Protection Association publishes
NFPA 70, commonly known as the National Electrical Code.
4. What does GFCI stand for?
A. Ground Fault Circuit Interrupter B. General Frequency
Control Indicator C. Grounded Feeder Current Installation D.
General Fault Connection Interface
Correct Answer: A. Ground Fault Circuit Interrupter.
Rationale: A GFCI detects differences between outgoing and
returning current and interrupts the circuit when a ground fault
is detected.
5. What is the main purpose of grounding an electrical
system?
A. Increase voltage B. Provide a path for fault current C. Reduce
electrical resistance to zero D. Increase energy consumption
Correct Answer: B. Provide a path for fault current.
Rationale: Grounding establishes a reference to earth and helps
limit dangerous voltage conditions. Equipment grounding
provides a low-impedance fault-current path to facilitate
protective-device operation.
6. Which device protects a circuit against excessive current?
,A. Switch B. Receptacle C. Circuit breaker D. Transformer
Correct Answer: C. Circuit breaker.
Rationale: A circuit breaker automatically opens a circuit when
excessive current flows, helping prevent overheating and
electrical fires.
7. What is the unit of electrical current?
A. Volt B. Ampere C. Ohm D. Watt
Correct Answer: B. Ampere.
Rationale: Current is measured in amperes (amps),
representing the rate of electric charge flow.
8. What is the unit of electrical resistance?
A. Watt B. Volt C. Ohm D. Ampere
Correct Answer: C. Ohm.
Rationale: Resistance is measured in ohms and describes
opposition to the flow of electrical current.
9. What does a voltmeter measure?
A. Current B. Resistance C. Voltage D. Power factor
Correct Answer: C. Voltage.
Rationale: A voltmeter measures the electrical potential
difference between two points in a circuit.
10. What is the purpose of an electrical service disconnect?
, A. Increase electrical frequency B. Disconnect power to the
electrical installation C. Increase circuit capacity D. Measure
electrical resistance
Correct Answer: B. Disconnect power to the electrical
installation.
Rationale: The service disconnect provides a means of
disconnecting the electrical supply from the premises under
specified conditions.
11. Which conductor normally carries current back to the
source in a single-phase grounded system?
A. Equipment grounding conductor B. Neutral conductor C.
Grounding electrode conductor D. Bonding jumper
Correct Answer: B. Neutral conductor.
Rationale: The neutral conductor is the grounded circuit
conductor that carries return current during normal operation.
12. What is the main function of an equipment grounding
conductor?
A. Carry normal load current B. Provide a low-impedance fault-
current path C. Increase circuit voltage D. Replace the neutral
conductor
Correct Answer: B. Provide a low-impedance fault-current path.
Rationale: The equipment grounding conductor connects
exposed conductive equipment parts to the grounding system
and helps protective devices clear faults.