S-95 FDNY TEST STUDY GUIDE Questions and Answers
with complete Solutions | Updated 2024
Question 1
What can an S-95 Certificate of Fitness holder do?
A. Only visual inspections on smoke alarms
B. Install fire alarm systems
C. Repair fire alarm systems
D. Design fire alarm systems
Correct Answer: A. Only visual inspections on smoke alarms
Rationale: An S-95 Certificate of Fitness holder is authorized to perform
only visual inspections on smoke alarms.
Question 2
What is the primary purpose of a fire alarm system on a premise?
A. To warn tenants and transmit signals indicating a fire condition to the
FDNY (Central Station)
B. To automatically extinguish fires
C. To provide lighting during an emergency
D. To control building access
Correct Answer: A. To warn tenants and transmit signals indicating
a fire condition to the FDNY (Central Station)
Rationale: The primary purpose of a fire alarm system is to warn tenants
,and transmit signals indicating a fire condition to the FDNY (also known as
Central Station).
Question 3
What is a Fire Alarm Control Panel (FACP)?
A. Monitors inputs and controls output through various types of circuits;
activates the building audible and visual devices connected to the fire
alarm (horn/strobes)
B. A device that extinguishes fires
C. A device that provides emergency lighting
D. A device that controls building access
Correct Answer: A. Monitors inputs and controls output through
various types of circuits; activates the building audible and visual
devices connected to the fire alarm (horn/strobes)
Rationale: The FACP monitors inputs and controls output through various
types of circuits and activates the building's audible and visual devices.
Question 4
What are the three types of signals?
A. Fire Alarm Signal, Supervisory Signals, and Trouble Signals
B. Alert, Alarm, and Trouble
C. Fire, Smoke, and Heat
D. Audible, Visual, and Tactile
Correct Answer: A. Fire Alarm Signal, Supervisory Signals, and
Trouble Signals
,Rationale: The three types of signals are Fire Alarm Signal, Supervisory
Signals, and Trouble Signals.
Question 5
What is a Fire Alarm Signal?
A. Manual fire alarm pull station, smoke detector, water flow switch in the
presence of a fire or fire signature
B. A signal indicating a system or device is compromised
C. A signal indicating battery failure
D. A signal indicating a ground fault
Correct Answer: A. Manual fire alarm pull station, smoke detector,
water flow switch in the presence of a fire or fire signature
Rationale: A Fire Alarm Signal is initiated by a manual fire alarm pull
station, smoke detector, or water flow switch in the presence of a fire or
fire signature.
Question 6
What are Supervisory Signals?
A. Signals which indicate that a system or device being monitored has
been compromised or is in an abnormal state
B. Signals indicating a fire
C. Signals indicating a trouble condition
D. Signals indicating a power failure
Correct Answer: A. Signals which indicate that a system or device
being monitored has been compromised or is in an abnormal state
Rationale: Supervisory Signals indicate that a system or device being
, monitored has been compromised or is in an abnormal state. They will
audibly and visually annunciate at the FACP and send a signal to an FDNY
approved central station.
Question 7
What are Trouble Signals?
A. Battery failure, AC failure, ground fault, open or short circuit on a wire,
phone line failure, internal component failure
B. Signals indicating a fire
C. Signals indicating a system is compromised
D. Signals indicating a normal condition
Correct Answer: A. Battery failure, AC failure, ground fault, open or
short circuit on a wire, phone line failure, internal component failure
Rationale: Trouble Signals indicate conditions such as battery failure, AC
failure, ground fault, open or short circuit on a wire, phone line failure, or
internal component failure.
Question 8
What is an Alarm Silence Switch or Button used for?
A. To silence the building audible and visual devices after evacuation is
complete while the source of alarm is being investigated
B. To reset the fire alarm system
C. To test the fire alarm system
D. To disable the fire alarm system
Correct Answer: A. To silence the building audible and visual devices
after evacuation is complete while the source of alarm is being
with complete Solutions | Updated 2024
Question 1
What can an S-95 Certificate of Fitness holder do?
A. Only visual inspections on smoke alarms
B. Install fire alarm systems
C. Repair fire alarm systems
D. Design fire alarm systems
Correct Answer: A. Only visual inspections on smoke alarms
Rationale: An S-95 Certificate of Fitness holder is authorized to perform
only visual inspections on smoke alarms.
Question 2
What is the primary purpose of a fire alarm system on a premise?
A. To warn tenants and transmit signals indicating a fire condition to the
FDNY (Central Station)
B. To automatically extinguish fires
C. To provide lighting during an emergency
D. To control building access
Correct Answer: A. To warn tenants and transmit signals indicating
a fire condition to the FDNY (Central Station)
Rationale: The primary purpose of a fire alarm system is to warn tenants
,and transmit signals indicating a fire condition to the FDNY (also known as
Central Station).
Question 3
What is a Fire Alarm Control Panel (FACP)?
A. Monitors inputs and controls output through various types of circuits;
activates the building audible and visual devices connected to the fire
alarm (horn/strobes)
B. A device that extinguishes fires
C. A device that provides emergency lighting
D. A device that controls building access
Correct Answer: A. Monitors inputs and controls output through
various types of circuits; activates the building audible and visual
devices connected to the fire alarm (horn/strobes)
Rationale: The FACP monitors inputs and controls output through various
types of circuits and activates the building's audible and visual devices.
Question 4
What are the three types of signals?
A. Fire Alarm Signal, Supervisory Signals, and Trouble Signals
B. Alert, Alarm, and Trouble
C. Fire, Smoke, and Heat
D. Audible, Visual, and Tactile
Correct Answer: A. Fire Alarm Signal, Supervisory Signals, and
Trouble Signals
,Rationale: The three types of signals are Fire Alarm Signal, Supervisory
Signals, and Trouble Signals.
Question 5
What is a Fire Alarm Signal?
A. Manual fire alarm pull station, smoke detector, water flow switch in the
presence of a fire or fire signature
B. A signal indicating a system or device is compromised
C. A signal indicating battery failure
D. A signal indicating a ground fault
Correct Answer: A. Manual fire alarm pull station, smoke detector,
water flow switch in the presence of a fire or fire signature
Rationale: A Fire Alarm Signal is initiated by a manual fire alarm pull
station, smoke detector, or water flow switch in the presence of a fire or
fire signature.
Question 6
What are Supervisory Signals?
A. Signals which indicate that a system or device being monitored has
been compromised or is in an abnormal state
B. Signals indicating a fire
C. Signals indicating a trouble condition
D. Signals indicating a power failure
Correct Answer: A. Signals which indicate that a system or device
being monitored has been compromised or is in an abnormal state
Rationale: Supervisory Signals indicate that a system or device being
, monitored has been compromised or is in an abnormal state. They will
audibly and visually annunciate at the FACP and send a signal to an FDNY
approved central station.
Question 7
What are Trouble Signals?
A. Battery failure, AC failure, ground fault, open or short circuit on a wire,
phone line failure, internal component failure
B. Signals indicating a fire
C. Signals indicating a system is compromised
D. Signals indicating a normal condition
Correct Answer: A. Battery failure, AC failure, ground fault, open or
short circuit on a wire, phone line failure, internal component failure
Rationale: Trouble Signals indicate conditions such as battery failure, AC
failure, ground fault, open or short circuit on a wire, phone line failure, or
internal component failure.
Question 8
What is an Alarm Silence Switch or Button used for?
A. To silence the building audible and visual devices after evacuation is
complete while the source of alarm is being investigated
B. To reset the fire alarm system
C. To test the fire alarm system
D. To disable the fire alarm system
Correct Answer: A. To silence the building audible and visual devices
after evacuation is complete while the source of alarm is being
