Assessor Moderator
Assessment mark %
ASSIGNMENT 2
DATE: 3rd June 2021 SESSION: 08h30 to 20h30
SUBJECT: Mechanical Engineering Design I CODE: MED21A
ASSESSOR: MKE RAMOSOEU
MODERATOR: N/A
INSTRUCTIONAL PROGRAMMES: Diploma In Engineering Technology In Mechanical
Engineering.
National Diploma In Mechanical Engineering.
CODE: DP_MEC
STATIONARY: 1. Use prescribed textbook, MECHANICAL DESIGN, Peter RN Childs, Elsevier
Butterworth-Heinemann, 2004, is only allowed.
2. non-programmable calculator.
DURATION OF PAPER: Minimum 12 hours MAXIMUM MARKS: 42
Allocated Marks:
Question: 1 (3) 2 (4) 3 (4) 4 (27) 5(4) T (42)
Assessor:
Moderator:
n/a
STUDENT TO COMPLETE or HAND COPY THIS BLOCK:
Declaration of Own Work
By submitting my work on this platform, I declare that: I have completed this assignment/assessment in
accordance with CUT's Code of Academic Integrity. All the work included in this assignment/assessment is my
own work; I did not consult any person or means other than that allowed in the assignment/assessment
instructions.
STUDENT NUMBER: SURNAME AND INITIALS:
(Write in Block Letters)
SIGNATURE OF STUDENT:
(You have read the instructions on page 2 of this booklet and on the Assignment 2 submission link on ethuto)
THIS PAPER CONSISTS OF 5 PAGES, INCLUDING THIS COVER PAGE.
, T2_MARK ASSESSMENT INSTRUCTIONS
1. Answer all questions using a BLACK/BLUE pen.
2. Students must write his/her student number on the middle top of each answer
sheet. Show all calculations, references & sketches with the necessary steps.
3. Submit the assignment in pdf format on the available submission link provided on
e-Thuto.
4. Students are given three attempts to submit assignments, and only the last
attempt will be marked.
5. No group assignments will be allowed. Instead, an individual student must
submit his/her own work.
6. SafeAssign tool from e-Thuto is used in this assignment.
7. Plagiarism is considered as severe misconduct, which can result in a student
being expelled from CUT.
For more information, read CUT Calendar 2021 (Table on Penalty Guidelines).
GOOD LUCK
Assessment mark %
ASSIGNMENT 2
DATE: 3rd June 2021 SESSION: 08h30 to 20h30
SUBJECT: Mechanical Engineering Design I CODE: MED21A
ASSESSOR: MKE RAMOSOEU
MODERATOR: N/A
INSTRUCTIONAL PROGRAMMES: Diploma In Engineering Technology In Mechanical
Engineering.
National Diploma In Mechanical Engineering.
CODE: DP_MEC
STATIONARY: 1. Use prescribed textbook, MECHANICAL DESIGN, Peter RN Childs, Elsevier
Butterworth-Heinemann, 2004, is only allowed.
2. non-programmable calculator.
DURATION OF PAPER: Minimum 12 hours MAXIMUM MARKS: 42
Allocated Marks:
Question: 1 (3) 2 (4) 3 (4) 4 (27) 5(4) T (42)
Assessor:
Moderator:
n/a
STUDENT TO COMPLETE or HAND COPY THIS BLOCK:
Declaration of Own Work
By submitting my work on this platform, I declare that: I have completed this assignment/assessment in
accordance with CUT's Code of Academic Integrity. All the work included in this assignment/assessment is my
own work; I did not consult any person or means other than that allowed in the assignment/assessment
instructions.
STUDENT NUMBER: SURNAME AND INITIALS:
(Write in Block Letters)
SIGNATURE OF STUDENT:
(You have read the instructions on page 2 of this booklet and on the Assignment 2 submission link on ethuto)
THIS PAPER CONSISTS OF 5 PAGES, INCLUDING THIS COVER PAGE.
, T2_MARK ASSESSMENT INSTRUCTIONS
1. Answer all questions using a BLACK/BLUE pen.
2. Students must write his/her student number on the middle top of each answer
sheet. Show all calculations, references & sketches with the necessary steps.
3. Submit the assignment in pdf format on the available submission link provided on
e-Thuto.
4. Students are given three attempts to submit assignments, and only the last
attempt will be marked.
5. No group assignments will be allowed. Instead, an individual student must
submit his/her own work.
6. SafeAssign tool from e-Thuto is used in this assignment.
7. Plagiarism is considered as severe misconduct, which can result in a student
being expelled from CUT.
For more information, read CUT Calendar 2021 (Table on Penalty Guidelines).
GOOD LUCK
