API 574 Study Guide Questions with Verified
Correct Answers
Why do injection points require enhanced inspection during operation?
Significant equipment problems have occurred as a result of injection points
Which of the following apply to corrosion from Injection Points?
Corrosion Rate may be 10 times (magnitude of order) higher than main stream and Damage
may be highly localized
Mixing points can have accelerated damage from: This
Corrosion and Vibration
Sulfidation of carbon steels begins to occur when the sulfur content is greater than
0.5% and the temperature exceeds:
500 F
Some of the crude unit piping operates at a temperature where sulfidation can occur.
Which material is most susceptible to attack?
A-53
A caustic piping system has external heat tracing. On this system, poorly designed heat
tracing can cause
stress corrosion cracking
Which of the following are needed for Contact-Point corrosion?
Oxygen, water, and deposit with a corrosive species
Open dummy legs supporting piping corrosion on the
, inside of leg and outside main pipe.
An insulated pipe at elevated temps is in a vapor service. This line is supported by
dummy legs. What is a potential problem?
Leg may create cool spot, causing condensation of corrodents in main line
CUI can be a major issue on insulated carbon steel piping systems operating between
10 - 350 °F.
CUI in carbon steel systems is particularly aggressive:
when operating temperatures cause frequent condensation and reevaporation of atmospheric
moisture.
CUI is an inspection concern for insulated piping operating at 500 °F. and:
is in intermittent service.
CUI can be an issue on insulated austenitic SS piping systems operating between
140 - 350 °F
CUI of austenitic stainless-steel piping
normally appears as chloride stress corrosion cracking.
Which of the following areas is least likely to be affected by Erosion-Corrosion?
Upstream of a pump
Which of the following is not a cause of fatigue cracking?
Viscosity cycles
Fatigue cracking can typically be first detected at:
Correct Answers
Why do injection points require enhanced inspection during operation?
Significant equipment problems have occurred as a result of injection points
Which of the following apply to corrosion from Injection Points?
Corrosion Rate may be 10 times (magnitude of order) higher than main stream and Damage
may be highly localized
Mixing points can have accelerated damage from: This
Corrosion and Vibration
Sulfidation of carbon steels begins to occur when the sulfur content is greater than
0.5% and the temperature exceeds:
500 F
Some of the crude unit piping operates at a temperature where sulfidation can occur.
Which material is most susceptible to attack?
A-53
A caustic piping system has external heat tracing. On this system, poorly designed heat
tracing can cause
stress corrosion cracking
Which of the following are needed for Contact-Point corrosion?
Oxygen, water, and deposit with a corrosive species
Open dummy legs supporting piping corrosion on the
, inside of leg and outside main pipe.
An insulated pipe at elevated temps is in a vapor service. This line is supported by
dummy legs. What is a potential problem?
Leg may create cool spot, causing condensation of corrodents in main line
CUI can be a major issue on insulated carbon steel piping systems operating between
10 - 350 °F.
CUI in carbon steel systems is particularly aggressive:
when operating temperatures cause frequent condensation and reevaporation of atmospheric
moisture.
CUI is an inspection concern for insulated piping operating at 500 °F. and:
is in intermittent service.
CUI can be an issue on insulated austenitic SS piping systems operating between
140 - 350 °F
CUI of austenitic stainless-steel piping
normally appears as chloride stress corrosion cracking.
Which of the following areas is least likely to be affected by Erosion-Corrosion?
Upstream of a pump
Which of the following is not a cause of fatigue cracking?
Viscosity cycles
Fatigue cracking can typically be first detected at: