Firefighter 2 Final Exam
Which pneumatic tools are often used for delicate cutting Whizzer saws
operations and can cut case hardened locks and steel?
Which proportioning method uses an external pump or Premixing method
head pressure to force foam concentrate into the fire
stream at the correct ratio for the water flow?
What is the term used to describe forward velocity Flow pressure
pressure at a discharge opening while water is flowing?
Which of the following is NOT a question that would be are appliances name brand?
asked concerning appliances during a residential fire
safety survey?
Are surge protectors being used?
Are appliances name brand?
Are electrical cords in good condition?
Are the units operating properly?
Which type of pressure can be measured with a pitot Flow pressure
tube and gauge?
Proportioning methods: When would batch mixing not be On large incidents because attack lines must be shut down when refilling an
effective? empty tank.
Water applied to ordinary combustibles usually _______. Reduce flame spread
Which type of valves are used to control the flow from Gate valves
the hydrant?
The _____ the wood, the easier to ignite and the faster it Smaller
loses structural integrity.
The threads on pump male discharge outlets are Hose caps
protected by fittings called _____ _____.
Who should begin stabilization of a patient trapped inside A rescuer with EMT training
a vehicle?
Name one element of patient removal: Covering sharp edges
Fixed-temperature heat detectors rated at _____(f)(c) 165 | 76
are common for living spaces.
Cribbing is most commonly used to _________. stabilize objects
Which type of test should be preformed by private Standard testing
contractors or fire department personnel?
, Firefighter 2 Final Exam
Which proportioning method is used with portable Premixing method
extinguishers, wheeled, extinguishers, skid-mounted
twin-agent units, and vehicle mounted tank systems?
One of the most important practices to address to making sure to maintain clear and unobstructed exit pathways
building occupants about fire safety is _______.
Normal pressure exiting a system before water is Static presssure
released from a hydrant is called ______.
Energy created by moving parts on machines, such as Mechanical heat energy
belts and bearings
Water received from treatment facilities is delivered to elevated
________ storage tanks before being distributed
throughout the area served.
State 3 facts about service testing: 1. The test area should be smooth and free from rock and debris
2. Hose should be tested in a paved area with room to lay out the hose
3. A water source sufficient for filling the hose is necessary
Describe Completed Foam: completed product after air is introduced into the foam solution
What can hide fire hazards and impede paths of egress? poor housekeeping
With the bank-down foam application method, the foam onto an object, allowing the foam to run down / onto the surface of the fuel.
stream is directed:
Winches should be positioned: as close to the object being pulled as possible
Which hydraulic tools may spread as much as 32 inches spreaders
(800mm) apart?
Which pneumatic tool can be used to vacuum loose soil air vacuum
from around victims buried in a trench collapse?
Which method of moving water uses a primary water gravity system
source located at a higher elevation than the distribution
system and delivers water to the system without the use
of pumps?
What is NOT a reason a hose clamp is used? to allow advancement of a charged hose line down stairs
Where should the hose be connected on a fire dept to the discharges on the opposite side of the pump panel
pumper when being used for service testing hose line?
What is the time span when presenting to young 15 minutes
children?
Which pneumatic tools are often used for delicate cutting Whizzer saws
operations and can cut case hardened locks and steel?
Which proportioning method uses an external pump or Premixing method
head pressure to force foam concentrate into the fire
stream at the correct ratio for the water flow?
What is the term used to describe forward velocity Flow pressure
pressure at a discharge opening while water is flowing?
Which of the following is NOT a question that would be are appliances name brand?
asked concerning appliances during a residential fire
safety survey?
Are surge protectors being used?
Are appliances name brand?
Are electrical cords in good condition?
Are the units operating properly?
Which type of pressure can be measured with a pitot Flow pressure
tube and gauge?
Proportioning methods: When would batch mixing not be On large incidents because attack lines must be shut down when refilling an
effective? empty tank.
Water applied to ordinary combustibles usually _______. Reduce flame spread
Which type of valves are used to control the flow from Gate valves
the hydrant?
The _____ the wood, the easier to ignite and the faster it Smaller
loses structural integrity.
The threads on pump male discharge outlets are Hose caps
protected by fittings called _____ _____.
Who should begin stabilization of a patient trapped inside A rescuer with EMT training
a vehicle?
Name one element of patient removal: Covering sharp edges
Fixed-temperature heat detectors rated at _____(f)(c) 165 | 76
are common for living spaces.
Cribbing is most commonly used to _________. stabilize objects
Which type of test should be preformed by private Standard testing
contractors or fire department personnel?
, Firefighter 2 Final Exam
Which proportioning method is used with portable Premixing method
extinguishers, wheeled, extinguishers, skid-mounted
twin-agent units, and vehicle mounted tank systems?
One of the most important practices to address to making sure to maintain clear and unobstructed exit pathways
building occupants about fire safety is _______.
Normal pressure exiting a system before water is Static presssure
released from a hydrant is called ______.
Energy created by moving parts on machines, such as Mechanical heat energy
belts and bearings
Water received from treatment facilities is delivered to elevated
________ storage tanks before being distributed
throughout the area served.
State 3 facts about service testing: 1. The test area should be smooth and free from rock and debris
2. Hose should be tested in a paved area with room to lay out the hose
3. A water source sufficient for filling the hose is necessary
Describe Completed Foam: completed product after air is introduced into the foam solution
What can hide fire hazards and impede paths of egress? poor housekeeping
With the bank-down foam application method, the foam onto an object, allowing the foam to run down / onto the surface of the fuel.
stream is directed:
Winches should be positioned: as close to the object being pulled as possible
Which hydraulic tools may spread as much as 32 inches spreaders
(800mm) apart?
Which pneumatic tool can be used to vacuum loose soil air vacuum
from around victims buried in a trench collapse?
Which method of moving water uses a primary water gravity system
source located at a higher elevation than the distribution
system and delivers water to the system without the use
of pumps?
What is NOT a reason a hose clamp is used? to allow advancement of a charged hose line down stairs
Where should the hose be connected on a fire dept to the discharges on the opposite side of the pump panel
pumper when being used for service testing hose line?
What is the time span when presenting to young 15 minutes
children?
