CDC 3E251 EXAMS SCRIPT 2026/2027 QUESTIONS AND
SOLUTIONS RATED A+
✔✔Which page of the AF Form 1800, Operator's Inspection Guide and Trouble Report,
has areas for operators to sign signifying the completion of the vehicle inspection? -
✔✔One
✔✔Where are the discrepancy item numbers placed on the AF Form 1800, Operator's
Inspection Guide and Trouble Report, when turning in a vehicle to maintenance? -
✔✔Left-handed column under "operator report"
✔✔In regards to vehicle maintenance, which action IS NOT normally and operator's
responsibility? - ✔✔Changing the transmission fluid
✔✔Failure to lubricate a piece of equipment or vehicle properly when required
constitutes - ✔✔Vehicle abuse
✔✔While cleaning a vehicle, where would you find an oil water separator to dispose of
engine degreaser? - ✔✔In the wash bay
✔✔What must be completed for an AF Form 171, Request for Driver's Training and
Addition to U.S. Government Drivers License, to be considered valid for licensing
purposes? - ✔✔Prescribed training
✔✔The only individuals who can sign your AF Form 171, Request for Driver's Training
and Addition to U.S. Government Drivers License, for licensing purposes are those -
✔✔Designated as "certifiers"
✔✔As a good rule-of-thumb, how many hours of training should you receive before
being licensed to operate a particular piece of equipment or vehicle? - ✔✔40
✔✔What two things MUST you have to receive a government driver's license? - ✔✔AF
Form 171 and state driver's license
✔✔The AF Form 2293 U.S. Air Force Motor Vehicle Operator Identification Card, is
used to establish and update what document? - ✔✔Individual driver record
✔✔What training must you, as a pavements and construction equipment operator, have
before you are certified to drive on the airfield? - ✔✔Airfield driver's education training
✔✔How often must pavement and construction equipment operators be recertified on
dump truck tailgate removal and installation? - ✔✔When needed
,✔✔Which soil horizon is the base for ALL TYPES of pavement constructions? - ✔✔B
✔✔The soil property "cohesion" refers to the soil's ability to - ✔✔Stick together when
dry
✔✔Which soil classification is made up of sand and gravel in the "B" horizon and has 50
percent or LESS material passing the No. 200 sieve? - ✔✔Coarse-grained
✔✔When compacting soil (subgrade) for stabilization, which function does a blanket or
insulating course serve? - ✔✔Helps reduce frost action
✔✔The device on the self-leveling level used to center the bubble on the bull's-eye is
the - ✔✔Leveling screw
✔✔When you carry the engineer level over rough terrain between points on a survey,
you should always - ✔✔Return it to the carrying case
✔✔When you are setting up the tripod of the engineer level on sloping surfaces, place
the third leg - ✔✔Uphill
✔✔When measuring vertical distances, who moves the target up or down until it is
bisected? - ✔✔Rod person
✔✔What is ACTUAL datum used as a reference for measuring elevations? - ✔✔Mean
sea level
✔✔Bench marks are survey markers denoting a precise elevation. Where would be a
good place to put a PERMANENT bench mark? - ✔✔Embedded into concrete
✔✔How many satellites make up the Global Positioning System (GPS)? - ✔✔24
✔✔The Global Positioning System (GPS) operates off of what type of signal? -
✔✔Radio
✔✔What type of slight tolerance projects is the Global Positioning System (GPS) not
well suited for? - ✔✔<1/4" from finish elevation
✔✔What percentage of increased accuracy are laser systems capable of providing over
conventional methods? - ✔✔50%
✔✔What is the MOST COMMON length of a carpenter's level we use on small projects?
- ✔✔4-foot
, ✔✔In working drawings, plan views correspond to the orientation of looking - ✔✔Down
on the project from a bird's eye view
✔✔What basic symbol in work drawings requires the GREATEST understanding? -
✔✔Line
✔✔A line composed of a series of short dashes on a construction drawing -
✔✔Represents a hidden line
✔✔When preparing a sketch for a sidewalk, which step should you perform FIRST? -
✔✔Physically check the construction site
✔✔When preparing a sketch for a sidewalk, what should you add in the clear space on
your working sketch? - ✔✔Special instructions
✔✔When managing a construction project, what dictates the types and amount of
equipment you have on your project? - ✔✔Size of the project
✔✔Which document do you use to list all the materials you need to order for a specific
construction project? - ✔✔Bill of Material (BOM)
✔✔If an item for your construction project costs more than the allowable government
purchase card (GPC) limit and supply is unable to purchase the item for you, you must
submit an - ✔✔AF Form 9 to the Contracting Squadron
✔✔Managing a construction project begins when - ✔✔Planning begins
✔✔When managing a construction project, what items let you know when it will be
complete? - ✔✔Timeline, schedule, and sequence of events
✔✔What is the FINAL step of managing a project? - ✔✔Follow-up
✔✔What are the two COMMON EXAMPLES of hazards associated with the use of
hand tools? - ✔✔Misuse and improper maintenance
✔✔When working in areas where sparks could be an ignition around flammable
substances, you should use hand tools made from what type of metal? - ✔✔Non-
ferrous metal
✔✔What is the life-span of a tool or item of equipment when properly maintained and
used under normal conditions? - ✔✔Indefinite
SOLUTIONS RATED A+
✔✔Which page of the AF Form 1800, Operator's Inspection Guide and Trouble Report,
has areas for operators to sign signifying the completion of the vehicle inspection? -
✔✔One
✔✔Where are the discrepancy item numbers placed on the AF Form 1800, Operator's
Inspection Guide and Trouble Report, when turning in a vehicle to maintenance? -
✔✔Left-handed column under "operator report"
✔✔In regards to vehicle maintenance, which action IS NOT normally and operator's
responsibility? - ✔✔Changing the transmission fluid
✔✔Failure to lubricate a piece of equipment or vehicle properly when required
constitutes - ✔✔Vehicle abuse
✔✔While cleaning a vehicle, where would you find an oil water separator to dispose of
engine degreaser? - ✔✔In the wash bay
✔✔What must be completed for an AF Form 171, Request for Driver's Training and
Addition to U.S. Government Drivers License, to be considered valid for licensing
purposes? - ✔✔Prescribed training
✔✔The only individuals who can sign your AF Form 171, Request for Driver's Training
and Addition to U.S. Government Drivers License, for licensing purposes are those -
✔✔Designated as "certifiers"
✔✔As a good rule-of-thumb, how many hours of training should you receive before
being licensed to operate a particular piece of equipment or vehicle? - ✔✔40
✔✔What two things MUST you have to receive a government driver's license? - ✔✔AF
Form 171 and state driver's license
✔✔The AF Form 2293 U.S. Air Force Motor Vehicle Operator Identification Card, is
used to establish and update what document? - ✔✔Individual driver record
✔✔What training must you, as a pavements and construction equipment operator, have
before you are certified to drive on the airfield? - ✔✔Airfield driver's education training
✔✔How often must pavement and construction equipment operators be recertified on
dump truck tailgate removal and installation? - ✔✔When needed
,✔✔Which soil horizon is the base for ALL TYPES of pavement constructions? - ✔✔B
✔✔The soil property "cohesion" refers to the soil's ability to - ✔✔Stick together when
dry
✔✔Which soil classification is made up of sand and gravel in the "B" horizon and has 50
percent or LESS material passing the No. 200 sieve? - ✔✔Coarse-grained
✔✔When compacting soil (subgrade) for stabilization, which function does a blanket or
insulating course serve? - ✔✔Helps reduce frost action
✔✔The device on the self-leveling level used to center the bubble on the bull's-eye is
the - ✔✔Leveling screw
✔✔When you carry the engineer level over rough terrain between points on a survey,
you should always - ✔✔Return it to the carrying case
✔✔When you are setting up the tripod of the engineer level on sloping surfaces, place
the third leg - ✔✔Uphill
✔✔When measuring vertical distances, who moves the target up or down until it is
bisected? - ✔✔Rod person
✔✔What is ACTUAL datum used as a reference for measuring elevations? - ✔✔Mean
sea level
✔✔Bench marks are survey markers denoting a precise elevation. Where would be a
good place to put a PERMANENT bench mark? - ✔✔Embedded into concrete
✔✔How many satellites make up the Global Positioning System (GPS)? - ✔✔24
✔✔The Global Positioning System (GPS) operates off of what type of signal? -
✔✔Radio
✔✔What type of slight tolerance projects is the Global Positioning System (GPS) not
well suited for? - ✔✔<1/4" from finish elevation
✔✔What percentage of increased accuracy are laser systems capable of providing over
conventional methods? - ✔✔50%
✔✔What is the MOST COMMON length of a carpenter's level we use on small projects?
- ✔✔4-foot
, ✔✔In working drawings, plan views correspond to the orientation of looking - ✔✔Down
on the project from a bird's eye view
✔✔What basic symbol in work drawings requires the GREATEST understanding? -
✔✔Line
✔✔A line composed of a series of short dashes on a construction drawing -
✔✔Represents a hidden line
✔✔When preparing a sketch for a sidewalk, which step should you perform FIRST? -
✔✔Physically check the construction site
✔✔When preparing a sketch for a sidewalk, what should you add in the clear space on
your working sketch? - ✔✔Special instructions
✔✔When managing a construction project, what dictates the types and amount of
equipment you have on your project? - ✔✔Size of the project
✔✔Which document do you use to list all the materials you need to order for a specific
construction project? - ✔✔Bill of Material (BOM)
✔✔If an item for your construction project costs more than the allowable government
purchase card (GPC) limit and supply is unable to purchase the item for you, you must
submit an - ✔✔AF Form 9 to the Contracting Squadron
✔✔Managing a construction project begins when - ✔✔Planning begins
✔✔When managing a construction project, what items let you know when it will be
complete? - ✔✔Timeline, schedule, and sequence of events
✔✔What is the FINAL step of managing a project? - ✔✔Follow-up
✔✔What are the two COMMON EXAMPLES of hazards associated with the use of
hand tools? - ✔✔Misuse and improper maintenance
✔✔When working in areas where sparks could be an ignition around flammable
substances, you should use hand tools made from what type of metal? - ✔✔Non-
ferrous metal
✔✔What is the life-span of a tool or item of equipment when properly maintained and
used under normal conditions? - ✔✔Indefinite