CQT EXAMS SCRIPT 2026/2027 QUESTIONS AND
SOLUTIONS RATED A+
✔✔In what general locations can the portable
oxygen bottles with mask be found in the main
cabin? - ✔✔In what general locations can the portable
oxygen bottles with mask be found in the main
cabin?
✔✔What mode is the FLT DK Door lock selector
spring loaded to? - ✔✔AUTO
✔✔What does the illumination of the LOCK FAIL
light indicate on the Flight Deck Door Lock Panel? - ✔✔Flight Deck Door Lock selector
in AUTO and door
lock has failed or Flight Deck Access System switch
is OFF.
✔✔What is the minimum supplemental oxygen
pressure required in the flight deck at 15 degrees
Celsius with a third Crew Member? - ✔✔655 AOM 16.1.2
✔✔What does the Overwing Exit annunciator
light indicate? - ✔✔The related overwing exit is not closed and locked,
or the related flight lock failed to engage when
commanded locked.
✔✔What sight references should be used to
adjust Pilot seat position? - ✔✔Sight along the upper surface of the
glareshield with a small amount of aircraft
nose structure visible.
• Sight over the control column (in the neutral
position) until the bottom edge of the
outboard display unit is visible.
✔✔You are cruising at FL390 when you experience a rapid decompression of the
aircraft. You
accomplish the CABIN ALTITUDE WARNING or Rapid Decompression Immediate
Action Steps and
all associated checklists successfully. Reaching 10,000 ft, you remove your oxygen
mask and
attempt to communicate with ATC via your headset boom mike, but they do not hear
you.
Q.1.20. Why? - ✔✔Because you have not closed the left oxygen mask
,panel door and pushed the PRESS TO TEST AND
RESET button.
✔✔It is a hot summer's day in mid-July, and you are operating a heavy -700 to
Albuquerque. You send
for PWB landing data and receive the following message:
BRK COOL. . What is the minimum brake cooling wait time
for a -700? - ✔✔62 minutes
✔✔Is there a way to shorten the minimum brake
cooling wait time? - ✔✔For a -700, yes. The cooling time may be waived if
actual brake temperature can be measured. The
measurement must be made between 10 and 15
minutes after parking and must be below 425°F. A
waiver to reduce the cooling time is not applicable to
the -800/MAX because these aircraft are equipped
with carbon brakes.
✔✔What is the impact now should you receive a
CAUTION - DO NOT APPROACH GEAR OR GATE
message? - ✔✔You will need to coordinate a location for the brake
cooling delay (away from the gate).
✔✔What are the three sources of Bleed Air? - ✔✔Engines, APU, or an external air
cart/source.
✔✔How is engine bleed obtained from the
compressor section in the NG and the MAX. - ✔✔NG
Engine bleed air is obtained from the 5th and 9th
stages of the compressor section. When 5th stage
low pressure bleed air is insufficient for the bleed air
system requirements, the high stage valve
modulates open to maintain adequate bleed air
pressure.
MAX8
Engine bleed air is obtained from the 4th and 10th
stages of the compressor section. When 4th stage
low pressure bleed air is insufficient for the bleed air
system requirements, the high stage valve
modulates open to maintain adequate bleed air
pressure.
✔✔Which systems rely on Bleed Air? - ✔✔• Air conditioning/pressurization
• Wing and engine thermal anti-icing
• Engine starting
, • Hydraulic reservoirs pressurization
• Water tank pressurization
• Nitrogen generation system
• Aspirated TAT probe
✔✔On the NG, what does a BLEED TRIP OFF
light mean, what happens, and can it be reset? - ✔✔• Illuminates when engine bleed air
temperature or pressure exceed a
predetermined limit.
• The engine bleed valve closes automatically.
• If temperature and/or pressure have returned
to a normal range, it can be reset with the
TRIP RESET button.
✔✔What is the purpose of the WING-BODY
OVERHEAT light? - ✔✔Indicates overheat from bleed air duct leak.
✔✔Where does the Wing-Body Overheat system
monitor for both the Left and Right side? - ✔✔• Left/Right engine strut
• Left/Right inboard wing leading edge
• Left/Right-hand air conditioning bay
✔✔What two unique areas does the Left side
Wing-Body Overheat system monitor? - ✔✔• Keel beam
• Bleed duct from APU
✔✔What is the purpose of the TRIP RESET
switch? - ✔✔700
Resets BLEED TRIP OFF, PACK TRIP OFF, and DUCT
OVERHEAT lights
800
Resets BLEED TRIP OFF, PACK, and ZONE TEMP lights
MAX
Resets BLEED, PACK, or ZONE TEMP lights
✔✔With the Isolation Valve switch in AUTO,
when will the valve automatically go from closed to
open? - ✔✔Opens automatically if either engine BLEED air or air
conditioning PACK switch is positioned OFF.
✔✔In the -700, what would cause the PACK
TRIP OFF light to illuminate? What happens? - ✔✔Indicates pack temperature has
exceeded limits.
Related pack valve automatically closes and mix
SOLUTIONS RATED A+
✔✔In what general locations can the portable
oxygen bottles with mask be found in the main
cabin? - ✔✔In what general locations can the portable
oxygen bottles with mask be found in the main
cabin?
✔✔What mode is the FLT DK Door lock selector
spring loaded to? - ✔✔AUTO
✔✔What does the illumination of the LOCK FAIL
light indicate on the Flight Deck Door Lock Panel? - ✔✔Flight Deck Door Lock selector
in AUTO and door
lock has failed or Flight Deck Access System switch
is OFF.
✔✔What is the minimum supplemental oxygen
pressure required in the flight deck at 15 degrees
Celsius with a third Crew Member? - ✔✔655 AOM 16.1.2
✔✔What does the Overwing Exit annunciator
light indicate? - ✔✔The related overwing exit is not closed and locked,
or the related flight lock failed to engage when
commanded locked.
✔✔What sight references should be used to
adjust Pilot seat position? - ✔✔Sight along the upper surface of the
glareshield with a small amount of aircraft
nose structure visible.
• Sight over the control column (in the neutral
position) until the bottom edge of the
outboard display unit is visible.
✔✔You are cruising at FL390 when you experience a rapid decompression of the
aircraft. You
accomplish the CABIN ALTITUDE WARNING or Rapid Decompression Immediate
Action Steps and
all associated checklists successfully. Reaching 10,000 ft, you remove your oxygen
mask and
attempt to communicate with ATC via your headset boom mike, but they do not hear
you.
Q.1.20. Why? - ✔✔Because you have not closed the left oxygen mask
,panel door and pushed the PRESS TO TEST AND
RESET button.
✔✔It is a hot summer's day in mid-July, and you are operating a heavy -700 to
Albuquerque. You send
for PWB landing data and receive the following message:
BRK COOL. . What is the minimum brake cooling wait time
for a -700? - ✔✔62 minutes
✔✔Is there a way to shorten the minimum brake
cooling wait time? - ✔✔For a -700, yes. The cooling time may be waived if
actual brake temperature can be measured. The
measurement must be made between 10 and 15
minutes after parking and must be below 425°F. A
waiver to reduce the cooling time is not applicable to
the -800/MAX because these aircraft are equipped
with carbon brakes.
✔✔What is the impact now should you receive a
CAUTION - DO NOT APPROACH GEAR OR GATE
message? - ✔✔You will need to coordinate a location for the brake
cooling delay (away from the gate).
✔✔What are the three sources of Bleed Air? - ✔✔Engines, APU, or an external air
cart/source.
✔✔How is engine bleed obtained from the
compressor section in the NG and the MAX. - ✔✔NG
Engine bleed air is obtained from the 5th and 9th
stages of the compressor section. When 5th stage
low pressure bleed air is insufficient for the bleed air
system requirements, the high stage valve
modulates open to maintain adequate bleed air
pressure.
MAX8
Engine bleed air is obtained from the 4th and 10th
stages of the compressor section. When 4th stage
low pressure bleed air is insufficient for the bleed air
system requirements, the high stage valve
modulates open to maintain adequate bleed air
pressure.
✔✔Which systems rely on Bleed Air? - ✔✔• Air conditioning/pressurization
• Wing and engine thermal anti-icing
• Engine starting
, • Hydraulic reservoirs pressurization
• Water tank pressurization
• Nitrogen generation system
• Aspirated TAT probe
✔✔On the NG, what does a BLEED TRIP OFF
light mean, what happens, and can it be reset? - ✔✔• Illuminates when engine bleed air
temperature or pressure exceed a
predetermined limit.
• The engine bleed valve closes automatically.
• If temperature and/or pressure have returned
to a normal range, it can be reset with the
TRIP RESET button.
✔✔What is the purpose of the WING-BODY
OVERHEAT light? - ✔✔Indicates overheat from bleed air duct leak.
✔✔Where does the Wing-Body Overheat system
monitor for both the Left and Right side? - ✔✔• Left/Right engine strut
• Left/Right inboard wing leading edge
• Left/Right-hand air conditioning bay
✔✔What two unique areas does the Left side
Wing-Body Overheat system monitor? - ✔✔• Keel beam
• Bleed duct from APU
✔✔What is the purpose of the TRIP RESET
switch? - ✔✔700
Resets BLEED TRIP OFF, PACK TRIP OFF, and DUCT
OVERHEAT lights
800
Resets BLEED TRIP OFF, PACK, and ZONE TEMP lights
MAX
Resets BLEED, PACK, or ZONE TEMP lights
✔✔With the Isolation Valve switch in AUTO,
when will the valve automatically go from closed to
open? - ✔✔Opens automatically if either engine BLEED air or air
conditioning PACK switch is positioned OFF.
✔✔In the -700, what would cause the PACK
TRIP OFF light to illuminate? What happens? - ✔✔Indicates pack temperature has
exceeded limits.
Related pack valve automatically closes and mix
