, [ Chapter 4: Creating Orthographic Projections in AutoCAD® ]
4) Enter your WCS .
5) If you are using Dynamic Input, set the Pointer Input Format to Absolute coordinates.
6) In the Viewport layer, draw a RECtangle that indicates the edges of your limits/paper
(11x8.5).
7) Zoom All
8) In your Visible layer, draw the visible lines of the front view.
a) Draw a RECtangle that is 3 inches long and 2 inches wide near the bottom left
corner of your drawing area.
b) Set your UCS origin to the bottom left corner of the front view.
c) Draw the 2 Lines within the rectangle.
d) Draw the Circle. (Note: n = diameter)
Note: Some visible features are missing, but this is all we can do for now.
4.11.2) Drawing the right side view
1) Turn your Object Snap on and set the following object snaps to be automatically
detected (Endpoint, Midpoint, Center, Quadrant, Intersection, Nearest, Perpendicular,
Extension).
4 - 31
, [ Chapter 7 – Dimensioning ]
The dimensioning standards presented in this chapter are in accordance with the
ASME Y14.5-2009 standard. This standard was created to establish a uniform way of
dimensioning an engineering drawing. This also minimizes errors that could occur while
reading or interpreting an engineering drawing. When a drawing conforms to the standard,
it is noted in the tolerance block as shown in Figure 7.2-1. Other common sense practices
will also be presented.
Figure 7.2-1: ASME Y14.5 – 2009 designation
7.3) DIMENSION APPEARANCE
7.3.1) Lines Used in Dimensioning
Dimensions require the use of dimension, extension and leader lines. All lines
used in dimensioning are drawn thin so that the print reader does not confuse them
with visible lines. Thin lines should be drawn at approximately 0.016 inch (0.3 mm).
Figure 7.3-1 illustrates the different features of a dimension and Figure 7.3-2 illustrates
different leader line configurations.
Dimension line: A dimension line is a thin solid line terminated by arrowheads, which
indicates the direction and extent of a dimension. A number is placed near the
midpoint to specify the feature’s size.
Extension line: An extension line is a thin solid line that extends from a point on the
drawing to which the dimension refers. There should be a visible gap between the
extension line and the object, and long extension lines should be avoided.
Leader line: A leader line is a straight inclined thin solid line that is usually terminated
by an arrowhead. It is used to direct a dimension, note, symbol, item number, or part
number to the intended feature on a drawing. Leader lines should not be drawn
vertical or horizontal, except for a short horizontal portion extending to the first or last
letter of the note. The horizontal part should not underline the note and may be omitted
entirely. Leader lines may be terminated by an arrow if it ends on the outline of an
object or without an arrowhead or with a dot (n1.5 mm, minimum) if it ends within the
outline of an object (see Figure 7.3-2). You should avoid creating long leaders,
crossing leaders, or leaders that are parallel to features on the drawing.
7-3
, [ Chapter 7 – Dimensioning ]
Dimensioning symbols replace text and are used to minimize language
barriers. Many companies produce parts all over the world. A print made in the U.S.A.
may have to be read in several different countries. The goal of using dimensioning
symbols is to eliminate the need for language translation. Table 7.3-4 shows some
commonly used dimensioning symbols. These symbols will be used and explained
throughout the chapter.
Term Symbol Term Symbol
Diameter n Depth / Deep x
Spherical diameter Sn Dimension not to scale 10
Radius R Square (Shape) o
Spherical radius SR Arc length 5
Reference dimension (8) Conical Taper y
Counterbore / Spotface v Slope z
Countersink w Symmetry i
or
=
Number of places 4X
Table 7.3-4: Dimensioning symbols
7.4) FEATURE DIMENSIONS
The following section illustrates the standard ways common features are
dimensioned.
a) A circle is dimensioned by its diameter and an arc by its radius using a leader line and
a note or linear dimension. Diameter dimensions of solid parts, such as a cylinder, is
given as a linear dimension. A diameter dimension is preceded by the symbol “n”,
and a radial dimension is preceded by the symbol “R”. On older drawings you may
see the abbreviation “DIA” placed after a diameter dimension and the abbreviation “R”
following a radial dimension. Figure 7.4-1 illustrates the diameter and radius
dimensions.
7-6
4) Enter your WCS .
5) If you are using Dynamic Input, set the Pointer Input Format to Absolute coordinates.
6) In the Viewport layer, draw a RECtangle that indicates the edges of your limits/paper
(11x8.5).
7) Zoom All
8) In your Visible layer, draw the visible lines of the front view.
a) Draw a RECtangle that is 3 inches long and 2 inches wide near the bottom left
corner of your drawing area.
b) Set your UCS origin to the bottom left corner of the front view.
c) Draw the 2 Lines within the rectangle.
d) Draw the Circle. (Note: n = diameter)
Note: Some visible features are missing, but this is all we can do for now.
4.11.2) Drawing the right side view
1) Turn your Object Snap on and set the following object snaps to be automatically
detected (Endpoint, Midpoint, Center, Quadrant, Intersection, Nearest, Perpendicular,
Extension).
4 - 31
, [ Chapter 7 – Dimensioning ]
The dimensioning standards presented in this chapter are in accordance with the
ASME Y14.5-2009 standard. This standard was created to establish a uniform way of
dimensioning an engineering drawing. This also minimizes errors that could occur while
reading or interpreting an engineering drawing. When a drawing conforms to the standard,
it is noted in the tolerance block as shown in Figure 7.2-1. Other common sense practices
will also be presented.
Figure 7.2-1: ASME Y14.5 – 2009 designation
7.3) DIMENSION APPEARANCE
7.3.1) Lines Used in Dimensioning
Dimensions require the use of dimension, extension and leader lines. All lines
used in dimensioning are drawn thin so that the print reader does not confuse them
with visible lines. Thin lines should be drawn at approximately 0.016 inch (0.3 mm).
Figure 7.3-1 illustrates the different features of a dimension and Figure 7.3-2 illustrates
different leader line configurations.
Dimension line: A dimension line is a thin solid line terminated by arrowheads, which
indicates the direction and extent of a dimension. A number is placed near the
midpoint to specify the feature’s size.
Extension line: An extension line is a thin solid line that extends from a point on the
drawing to which the dimension refers. There should be a visible gap between the
extension line and the object, and long extension lines should be avoided.
Leader line: A leader line is a straight inclined thin solid line that is usually terminated
by an arrowhead. It is used to direct a dimension, note, symbol, item number, or part
number to the intended feature on a drawing. Leader lines should not be drawn
vertical or horizontal, except for a short horizontal portion extending to the first or last
letter of the note. The horizontal part should not underline the note and may be omitted
entirely. Leader lines may be terminated by an arrow if it ends on the outline of an
object or without an arrowhead or with a dot (n1.5 mm, minimum) if it ends within the
outline of an object (see Figure 7.3-2). You should avoid creating long leaders,
crossing leaders, or leaders that are parallel to features on the drawing.
7-3
, [ Chapter 7 – Dimensioning ]
Dimensioning symbols replace text and are used to minimize language
barriers. Many companies produce parts all over the world. A print made in the U.S.A.
may have to be read in several different countries. The goal of using dimensioning
symbols is to eliminate the need for language translation. Table 7.3-4 shows some
commonly used dimensioning symbols. These symbols will be used and explained
throughout the chapter.
Term Symbol Term Symbol
Diameter n Depth / Deep x
Spherical diameter Sn Dimension not to scale 10
Radius R Square (Shape) o
Spherical radius SR Arc length 5
Reference dimension (8) Conical Taper y
Counterbore / Spotface v Slope z
Countersink w Symmetry i
or
=
Number of places 4X
Table 7.3-4: Dimensioning symbols
7.4) FEATURE DIMENSIONS
The following section illustrates the standard ways common features are
dimensioned.
a) A circle is dimensioned by its diameter and an arc by its radius using a leader line and
a note or linear dimension. Diameter dimensions of solid parts, such as a cylinder, is
given as a linear dimension. A diameter dimension is preceded by the symbol “n”,
and a radial dimension is preceded by the symbol “R”. On older drawings you may
see the abbreviation “DIA” placed after a diameter dimension and the abbreviation “R”
following a radial dimension. Figure 7.4-1 illustrates the diameter and radius
dimensions.
7-6