Electrical Wiring Commercial (18th
Edition) – Phil Simmons – Solution
Manual| Complete Chapters
1. What section of a commercial building's specification contains a list of
contract documents?
• A) Supplementary General Conditions
• B) General Clauses and Conditions
• C) Electrical Specifications
• D) Architectural Drawings
Answer: B
Rationale: A list of the contract documents is contained in the General Clauses
and Conditions section of the commercial building's specifications. The
Supplementary General Conditions covers job site requirements, not contract
documents.
2. The requirement for temporary light and power at the job site will be found
in what portion of a commercial building's specification?
• A) General Clauses and Conditions
• B) Electrical Layout Drawings
• C) Supplementary General Conditions
• D) Site Plan
Answer: C
Rationale: The Supplementary General Conditions specifies the job site
requirements for temporary light and power. This may be the general contractor's
or electrical contractor's responsibility depending on the contract.
,3. The electrician uses the Schedule of Working Drawings for what purpose?
• A) To order materials
• B) To determine whether all drawings are at hand
• C) To calculate load requirements
• D) To schedule inspections
Answer: B
Rationale: The electrician uses the Schedule of Working Drawings to determine
whether all of the drawings are at hand, as information on "the other sheets" is
important for coordinating with other contractors.
4. From which source would you find ceiling height information?
• A) Electrical layout drawings
• B) Sections, Sheet A6
• C) Site plan
• D) Elevations
Answer: B
Rationale: Ceiling height information is found in the sections, typically on Sheet
A6 of the architectural drawings.
5. From which source would you find electrical receptacle style information?
• A) Electrical layout drawings
• B) Electrical symbol schedule, Chapter 2, Figure 2-6
• C) Elevations
• D) Site plan
,Answer: B
Rationale: The electrical receptacle style is found in the electrical symbol
schedule, typically in Chapter 2, Figure 2-6.
6. From which source would you find electrical outlet location information?
• A) Sections
• B) Site plan
• C) Electrical layout drawings, Sheets E1, E2, and E3
• D) Elevations
Answer: C
Rationale: Electrical outlet locations are shown on the electrical layout drawings,
typically Sheets E1, E2, and E3.
7. From which source would you find exterior wall finishes information?
• A) Electrical layout drawings
• B) Sections
• C) Site plan
• D) Elevations, Sheets A4 and A5
Answer: D
Rationale: Exterior wall finishes are found on the elevations, typically Sheets A4
and A5.
8. From which source would you find grading elevations?
• A) Sections
• B) Electrical layout drawings
• C) Site plan, Sheet A4
, • D) Elevations
Answer: C
Rationale: Grading elevations are found on the site plan, typically Sheet A4.
9. From which source would you find panelboard schedules?
• A) Sections
• B) Elevations
• C) Electrical layout drawings, Sheet E4
• D) Site plan
Answer: C
Rationale: Panelboard schedules are found on the electrical layout drawings,
typically Sheet E4.
10. From which source would you find room width information?
• A) Sections
• B) Architectural floor plan, Sheets A1, A2, and A3
• C) Site plan
• D) Elevations
Answer: B
Rationale: Room width is found on the architectural floor plan, typically Sheets
A1, A2, and A3.
11. Which organization publishes the National Electrical Code?
• A) IAEI
• B) NFPA
• C) UL
Edition) – Phil Simmons – Solution
Manual| Complete Chapters
1. What section of a commercial building's specification contains a list of
contract documents?
• A) Supplementary General Conditions
• B) General Clauses and Conditions
• C) Electrical Specifications
• D) Architectural Drawings
Answer: B
Rationale: A list of the contract documents is contained in the General Clauses
and Conditions section of the commercial building's specifications. The
Supplementary General Conditions covers job site requirements, not contract
documents.
2. The requirement for temporary light and power at the job site will be found
in what portion of a commercial building's specification?
• A) General Clauses and Conditions
• B) Electrical Layout Drawings
• C) Supplementary General Conditions
• D) Site Plan
Answer: C
Rationale: The Supplementary General Conditions specifies the job site
requirements for temporary light and power. This may be the general contractor's
or electrical contractor's responsibility depending on the contract.
,3. The electrician uses the Schedule of Working Drawings for what purpose?
• A) To order materials
• B) To determine whether all drawings are at hand
• C) To calculate load requirements
• D) To schedule inspections
Answer: B
Rationale: The electrician uses the Schedule of Working Drawings to determine
whether all of the drawings are at hand, as information on "the other sheets" is
important for coordinating with other contractors.
4. From which source would you find ceiling height information?
• A) Electrical layout drawings
• B) Sections, Sheet A6
• C) Site plan
• D) Elevations
Answer: B
Rationale: Ceiling height information is found in the sections, typically on Sheet
A6 of the architectural drawings.
5. From which source would you find electrical receptacle style information?
• A) Electrical layout drawings
• B) Electrical symbol schedule, Chapter 2, Figure 2-6
• C) Elevations
• D) Site plan
,Answer: B
Rationale: The electrical receptacle style is found in the electrical symbol
schedule, typically in Chapter 2, Figure 2-6.
6. From which source would you find electrical outlet location information?
• A) Sections
• B) Site plan
• C) Electrical layout drawings, Sheets E1, E2, and E3
• D) Elevations
Answer: C
Rationale: Electrical outlet locations are shown on the electrical layout drawings,
typically Sheets E1, E2, and E3.
7. From which source would you find exterior wall finishes information?
• A) Electrical layout drawings
• B) Sections
• C) Site plan
• D) Elevations, Sheets A4 and A5
Answer: D
Rationale: Exterior wall finishes are found on the elevations, typically Sheets A4
and A5.
8. From which source would you find grading elevations?
• A) Sections
• B) Electrical layout drawings
• C) Site plan, Sheet A4
, • D) Elevations
Answer: C
Rationale: Grading elevations are found on the site plan, typically Sheet A4.
9. From which source would you find panelboard schedules?
• A) Sections
• B) Elevations
• C) Electrical layout drawings, Sheet E4
• D) Site plan
Answer: C
Rationale: Panelboard schedules are found on the electrical layout drawings,
typically Sheet E4.
10. From which source would you find room width information?
• A) Sections
• B) Architectural floor plan, Sheets A1, A2, and A3
• C) Site plan
• D) Elevations
Answer: B
Rationale: Room width is found on the architectural floor plan, typically Sheets
A1, A2, and A3.
11. Which organization publishes the National Electrical Code?
• A) IAEI
• B) NFPA
• C) UL
